Dress pattern 56 58 size. Pattern of a dress on the big size. How to check the basic pattern

Dear masters! The editors of the site receive a huge number of letters with a request to develop and publish as many fashionable and elegant models in large sizes as possible. We understand that it is difficult to buy beautiful and high-quality clothes for a non-standard figure in stores, and we try to take into account all your wishes and fulfill them. However, in order to model the desired style of a dress or blouse, a basic pattern or base of the dress is required, and it is with its construction that one must begin. Needless to say, the request to publish a basic pattern for download in large size is the champion among your requests? Today we are happy to fulfill the desire of many of our readers, women of luxurious forms, we publish a basic pattern for download in sizes 52-54-56, and we hope that this will help you create clothes that fit perfectly on the figure, and for someone, it may become new stage of the creative journey.

In addition to the back and front patterns, we also developed a one-seam sleeve pattern, so that you can sew not only dresses, but also blouses, and even light jackets using this pattern.

Basic dress pattern for 52-54-56 sizes

But you will deal with the adjustment a little later, and only if it is required. And first you need to download and print the pattern.

How to print a basic pattern

We have prepared for you two options for a pattern for printing - you can download and print the drawing in A0 format and in A4 format. The A0 format will allow you to print the pattern in full size, and you do not have to glue the sheets. Printers of such a large format are in the copy centers of any city.

On A4 format, the image is divided into 16 sheets, you can print it on any printer, and then glue the sheets into a single pattern according to the alignment marks. Some printers are capable of shrinking the image (if the appropriate settings are set), and to prevent this from happening, we placed a test square with a side length of 100 mm on the pattern (see Fig. 1 mark 1).

IMPORTANT! After you glue the pattern, be sure to check the length of the test square!

After the pattern is printed, select your size in the upper left corner (Fig. 1 mark 2). Each dimension has its own line type. Circle the pattern along the contour as shown in fig. 1 on the tracing paper and proceed to check the pattern.

IMPORTANT! An additional traveling tuck on the front half of the drawing (left) should be made only if additional fitting is required.

Rice. 1. How to reshoot a basic dress pattern

How to check the basic pattern

To check the pattern, keep your measurements handy. Take measurements according to the pattern:

Y1=Measuring Back Waist Length (DTS)
Y2= measure length to waist front (accident)
X1 + X2 = measurement Bust circumference with an increase of about 3-4 cm
х3+х4+х5+х6=measuring waist circumference with an increase of about 2-3 cm
X7+X8=Measuring Hip circumference with an increase of about 2-3 cm
Z1= measurement Arm circumference with an increase of about 3-4 cm.

Rice. 2. How to check the basic pattern

How to download a basic dress pattern for sizes 52-56

To download patterns in A0 or A4 formats, click on the appropriate button. Instructions for working with patterns are given earlier in this article.

You will find even more new interesting ideas on the Anastasia Korfiati Sewing School website. Subscribe to free lessons and sew fashionable clothes with us!

Today we will learn how to model two of them: a dress and a jacket:

dress pattern

Let's take a closer look at the photo of the dress, the pattern of which we have to do. Seam under the bust, with 7/8 sleeves and a wide skirt that is gathered at the junction with the bodice. The bottom of the sleeve is gathered with a drawstring with an elastic band or braid. The mouth is expanded, round, processed by a slanting inlay. Breast tuck from the side seam under the armhole. Pockets are processed on the skirt - the entrance to the pockets can be made in the side seam, or it can be “framed”. Because the dress is loose - no clasp is required. The fabric for tailoring is linen, although you can use woolen crepe and mixed fabrics for the cold season if desired.

To model the model, we needIt can be easily generated on our website according to your own individual measurements. It's very easy and fast, just enter your measurements in the form, online will do the rest for you. You can print on any printer, even at home, or save to a flash card and print at a copy center. Technological allowances for freedom of fit are already included in the construction and have the minimum required values. We will correct the fit degree of our model a little later in the modeling process by retracting the side seams. So, here's what we got.

Print on any printer and cut out. Waist darts will be ignored. Next, we model on paper.

1 step. We straighten the side seams, taking them a little to the side for more volume in the waist area and even higher, under the armhole. We lengthen the future pattern of the dress, in accordance with the sketch or at your request.

2 step. Raise the waist line 5 cm up. Bring the chest tuck into the side seam under the armhole.

3 step. Expand and deepen the neck line. Cut off the bodice from the skirt on the details of the back and front pattern, then the modeling will take place on the details of the skirt.

4 step. On the details of the skirt pattern, mark the longitudinal lines along which to cut and push the details to increase the volume of the skirt. On the front part of the skirt panel, mark the location of the pocket and the pattern of the burlap itself. The entrance to the pocket is located in the side seam and starts 12 cm down from the line of attachment of the skirt to the bodice detail, see fig.

5 step. Sleeve modeling. Expand the sleeve at the bottom to the width of the sleeve under the armhole, cut along the middle, part according to the diagram so that the pattern is trapezoidal (the sleeve below is wider than under the armhole). Adjust the bottom line of a slightly arched curve. The bottom of the sleeves in the dress is gathered with an elastic band.

Dress pattern is ready. Sew - boast on ours)

Jacket pattern

Unlined jacket, made of dense fabric such as loden, boiled jersey or any other similar with non-shrinking cuts. One-piece sleeve, apache collar, without fasteners, patch pockets with flaps on the front.

For modeling, we will use, which you can also generate using our website. Allowances for loose fit are automatically added to the generator.

1 step. To begin with, let's draw auxiliary lines from the highest points of the neckline of the front and back through points lying 2 cm above the end points of the shoulder, with a length equal to the length of the sleeve + the length of the shoulder. We mark the deepening of the armholes by 4-5 cm with transverse marks. see fig.

2 step. From the points that raise the line of the shoulder, draw sloping lines of the upper cuts of the sleeve. see fig. The width of the sleeve at the bottom is equal to the girth of the wrist + an increase in freedom (7-10 cm).

3 step. Expand and deepen the neck. We draw the line of the board parallel to the middle line of the shelf at a distance of 6 cm.

4 step. The construction of the apache collar.

Through the highest point and the middle (lying at the intersection of the midline of the shelf and the neckline) point, draw an auxiliary straight line, extend it upwards and set aside a segment on it equal to the length of the neckline of the back. Draw this segment with a curved line. This is the line for stitching the collar into the neck of the back. The floor is at a right angle to it, to the right, set aside the width of the collar 8-9 cm and connect it with a curved convex-concave line, see Fig., With a point that limits the apache collar. According to the sketch/photo of the model, the end of the collar lies at the level of the armhole depth, and its width is approximately 20-25 cm.

5 step. Construction of a patch pocket.

The pattern of the original jacket is ready. Good luck with your sewing! Be beautiful!

Pattern-base for full figures, for sizes 50-58, built according to the same method as But differs in some specific features: allowances and a line of the shoulder seam, associated with the fact that a magnificent bust and, very often, a full waist and stomach, require other allowances for a loose fit. And must be measured especially carefully.

Therefore, in this article, I decided to place a table with the real measurements of my clients, 50-58 sizes, with the types of figures "apple", "pear", "hourglass". They will help you build your own custom base pattern.

Table of measurements 50-58 sizes.

Features of calculations for patterns-bases 50-58 sizes.

Rule 1

If for sizes 44-50 0.5 cm is added to half of the chest circumference, then for patterns for full figures 54-58 - 0.7-1 cm. This is done so that the side seam does not move towards the front.

Rule 2

When constructing a front pattern of 54-58 sizes, due to the large size of the tuck - 11-15 cm, the shoulder seam line can be drawn at a significant slope. Because of this armhole, the front is small and short for such sizes. It is very difficult to sew a sleeve into it correctly and beautifully.

Therefore, when I build a pattern, I usually check the shoulder slope line with a control measure - oblique chest height - VGk. Even if it coincides with the drawn line of the shoulder, I “raise” the shoulder seam by 1-1.5 cm - the picture on the bottom collage. And, as a rule, when trying on, if we sew a model of a dress with sleeves, we deepen the armhole by 1.5-3 cm for blouses and dresses, and for jackets - by 2-4 cm

Rule 3

For full apple-shaped figures, the side seam line usually passes through the points at the intersection of the bust, hips and control line. And the width of the side and central tucks is only 2-2.5 cm

For hourglass and pear figures, it is more difficult to build a base pattern due to the large difference in the size of the chest, waist and hips. For example, if the exhaust gas is 110 cm, from is 90 cm, and the OB is 118, the width of the darts is 3 cm

As a result, a rather sharp bend in the side seam is obtained, which is difficult to iron when sewing a dress or jacket. Therefore, it is preferable to sew models with a central seam on the back, and redistribute the width of the darts. If the deflection along this seam is 1 cm, then the side tucks can be reduced by 0.5-0.7 cm each. And I prefer to sew a zipper, when the style allows it, into the central seam of the back. If the model of the dress with a skirt is “semi-sun”, then the zipper is sewn into the side seam.

Calculations for pattern base 50-58 sizes.

The allowance for a loose fit to the chest circumference, for a dress and a blouse, even an adjacent silhouette, it is better to make 7-8 cm, for a semi-adjacent and for a jacket - 9-10 cm

Calculation of measurements for size 50.

OT - 78 or OT - 84

(OG + 8): 2 = 108: 2 = 54: 2 = 27

For the front pattern, add 0.5, for the back pattern, subtract 0.5 cm

OG on the front chest line - 27.5

OG back - 26.5

Calculation of the dimensions of the darts.

From \u003d 78 cm + 4 \u003d 82: 2 \u003d 41

From the calculated measurement of half the OG with an allowance, we subtract the resulting value of half the waist with allowances: 54 - 41 \u003d 13: 4 \u003d 3.2 - for an hourglass figure.

With OT \u003d 84, the size of the darts is as follows: 84 + 4 \u003d 88: 2 \u003d 44

54 - 44 \u003d 10 cm: 4 \u003d 2.5 cm - for an apple silhouette figure.

Calculation of the size of the hip line.

(OB + 4): 2 = 104 + 4 = 108: 2 = 54

For a figure with such measurements, the points of the front line of the chest and the line of the hips are located on the same control line.

If OB \u003d 110 cm, then after calculating: (110 + 4 \u003d 114) : 2 \u003d 57, the difference between half the circumference of the chest with allowances and half the circumference of the hips with allowances, would be 3 cm.

57 - 54 \u003d 3: 2 \u003d +1.5 cm - this value must be set aside from the control line on the front and back pattern along the hips. For the front - to the left, for the back - to the right.

Calculation of measurements for a pattern of 52 sizes.

OG \u003d (104 + 8) : 2 \u003d 112: 2 \u003d 56: 2 \u003d 28

0.5 = 28.5 - front, - 0.5 = 27.5 - back

OT \u003d (92 + 4): 2 \u003d 48

Darts = 56 - 48 = 8: 4 = 2 cm - each tuck

OB \u003d (112 + 4) : 2 \u003d 116: 2 \u003d 58

58 - 56 \u003d 2 cm: 2 - + 1 cm along the hip line from the control line.

Calculation of measurements for size 54.

OG \u003d (108 + 8) : 2 \u003d 116: 2 \u003d 58: 2 \u003d 29

OG transfer \u003d 29 + 0.7 \u003d 29.7

OG back \u003d 29 - 0.7 \u003d 28.3

From = (94 + 4) : 2 = 98: 2 = 49

Darts = 58 - 49 = 11: 4 = 2.7

OB \u003d (116 + 4) : 2 \u003d 120: 2 \u003d 60 - 58 \u003d 2: 2 \u003d +1 cm from the control lines along the hip line

Calculation of measurements for size 58.

OG \u003d (116 + 8) : 2 \u003d 124: 2 \u003d 62: 2 \u003d 31

OG transfer = 31 + 1 = 32

Back exhaust gas 31 - 1 = 30

OT \u003d (98 + 4) \u003d 2 \u003d 102: 2 \u003d 51

62 - 51 \u003d 11: 4 \u003d 2.7 cm - darts

OB \u003d (122 + 4) : 2 \u003d 126: 2 \u003d 63

63 - 62 \u003d 1 cm: 2 \u003d + 0.5 cm from the point of the reference line on the line of the hips.

In order to build a base pattern for a dress with a straight silhouette, draw lines parallel to the middle of the front and back, from a point on the line of the hips, to the required length of the dress.

Using such a pattern, if it is built accurately and tested, you will be able to model and sew any of the models.

For a trapezoid dress, continue the control line to the required length and set the point of inclination of the side seam at a distance of 12-22 cm to the left of it - for the front half of the pattern. For the pattern of the back, respectively, to the right. This distance can be increased to 25 cm, but no more, especially if the length of the dress is up to the knee. The side seams will simply “fold” inward, and the dress will look sloppy.

If you want a more flared dress, then choose a model with an undercut under the bust and a half-sun or A-line cut at the bias. You can choose a dress model with reliefs - each detail changes along the bottom line to the required width.

This section is dedicated to curvy women. We will consider and learn how to build patterns using several methods that are used when sewing clothes for obese women. Here, as in previous lessons, we use step by step instructions building drawings of the base of the dress, sleeves, etc.

As an example, in the first option, we will take measurements that correspond to size 54 (bust circumference 108cm), so to speak, for women of medium splendor. In the second option, we use, as an example, measurements corresponding to size 60 (bust circumference 120cm), for women with more magnificent forms. In both cases, we build patterns for the base of the dress. semiadjacent silhouette, in accordance with this, we take into account the allowance for a free fit along the lines of the chest, waist and hips.
You take measurements from your figure or from the figure of the person for whom you will sew a dress.
In any case, we recommend that after building a drawing and making a pattern, check it on something simple. For example, sew a dressing gown from cheap fabric. If you are not at all sure, use an old sheet or another thing that has served its age for sewing.

As a parting word: I wish you courage in your endeavors, perseverance, perseverance and patience in achieving your goal. Step by step, moving forward, you will overcome the path to perfection.
We use exactly step by step drawing instructions to demonstrate and convince you that in fact everything is not as complicated as it might seem at first glance. When you look at the finished drawing of the base pattern and have not encountered anything like this before, you may get the impression that all this is incredibly difficult and almost impossible. However, I note that the impossible is most often just something that we have not yet tried to do. Good luck!

SEMI-FITTING DRESS FOR WOMEN OF MIDDLE COMPLETENESS (for example, size 54)

To build a pattern drawing, you need to take the following measurements:
Recommendation: Take the correct measurements. The whole result of your efforts will depend on this.
In order to take measurements more accurately, it is necessary to mark the starting points: the seventh cervical vertebra, which is well defined when the head is tilted, as well as the shoulder line at the base of the neck and at the junction of the arm with the shoulder. Use pins or chalk for this if the woman is dressed. If you need to put a point on the body, use a felt-tip pen, which is easily erased with an alcohol-containing liquid after the end of this procedure.
It’s good if the person you are taking measurements from is wearing a thin dress, or better, only underwear. He, or rather she, since we are talking about a woman, should stand straight, without tension, i.e. maintain your normal posture. That is what I draw your attention to. Because, often a woman, when taking measurements or trying on, especially if she sees her reflection in the mirror, wanting to look slimmer, tightens her stomach, straightens her back, etc. The desire to look better is a good desire, but when taking measurements, it can distort the real state of things. And a well-fitting dress on fitting, in ordinary life, will not be as comfortable as we would like, and as it should be.
Therefore, taking into account the above, turn the client away from the mirror, distract him with a peaceful conversation, tie a string around his waist, mark the starting points and proceed to measurements.

There are some differences between the proposed methods. in the methods of taking measurements, in the number of measurements, in the name of the measurements, etc. In this technique, the procedure for taking measurements is as follows:

*Name of measurements and symbols*	cm	*Taking measurements*
Product length (Di)		Measure from the cervical point (seventh cervical vertebra), bringing the centimeter to the waist and to the required length.
Armhole depth (Gpr)		Measure from the seventh cervical vertebra to a horizontal line drawn with a centimeter through the armpits.
Back length to waist (Dst)		Measured from the seventh cervical vertebra to the waist line, taking into account the prominence of the shoulder blades. To do this, a thin ruler can be attached to the protruding points of the shoulder blades, the centimeter tape should pass over the ruler.
Back width (W)		Measure horizontally along the shoulder blades, between the upper corners of the armpits.
Half neck (Ssh)		The measuring tape should run along the base of the neck, behind the seventh cervical vertebrae, in front of the jugular cavity (depression).
Semi-girth of the chest 1st (СгI)		The centimeter tape runs horizontally, behind the protruding points of the shoulder blades, in front above the base of the chest.
Half bust 2nd (CrII)		The centimeter tape runs horizontally behind the protruding points of the shoulder blades, in front along the protruding points of the chest.
Groove opening size (Brv)		Measured vertically. It is removed simultaneously with the measurements of the half-girths of the chest. This is the distance from the base of the chest to its highest point.
Waist (St)		Measure horizontally at the narrowest point.
Half hips (Sat)		Measured horizontally, behind the protruding points of the buttocks, in front, taking into account the bulge of the abdomen.
Root height (Br)		Measure along the back from the shoulder at the base of the neck to the waist line. The measuring tape runs parallel to the spine.
Back shoulder height (Vps)		Measure along the back from the point of articulation of the arm with the shoulder to the waist.
Armhole Width (Spr)		It is measured horizontally under the arm: from the place of articulation of the arm with the body from the back side to the articulation of the arm with the body from the front side. It can be calculated using a ruler located horizontally in the armpit.
Side length (db)		Measure from the back side from the top edge of the ruler located in the armpit to the waist line.
Shoulder length (Dp)		Measure along the shoulder from the base of the neck to the point of articulation of the arm with the shoulder.
Chest Height (Hg)		Measure from the shoulder line at the base of the neck to the protruding point of the chest.
Front Shoulder Height (RH)		Measure from the point of articulation of the arm with the shoulder to the waist.
Front length to waist (Dpt)		Measure from the shoulder at the base of the neck to the waistline.
Center of the chest (Cg)		Measure horizontally between the most protruding points of the chest.
Front Width (W)		Measured horizontally above the base of the chest between the corners of the armpits.
Width of the front at the protruding points of the chest (ShpII) Control measurement		It is measured horizontally between the corners of the armpits at the most protruding points of the chest.
Sleeve length (dr)		It is measured from the point of articulation of the arm with the shoulder to the desired length.
Sleeve length to elbow (DRL)		Measured from the point of articulation of the arm with the shoulder to the elbow.
Arm circumference (Op)		Measured horizontally at the fullest upper part of the arm (at armpit level).
Girth of the wrist (hand) Oz		Measured at the wrist joint, taking into account the bone.
Free fit allowances For a free fit, add 4-5 cm to the measurement of the second half-girth of the chest Cr II, to the measure of the half-girth of the hips Sat - 3 cm and to the measure of the half-girth of the waist St - 2 cm.

Let's start building.
We draw in the right corner of the prepared sheet of paper a right angle with a vertex at a point R(Fig. 1).

Dress length.
From the point P down we postpone the taken measurement of the length of the dress Di(100 cm) and put a point H.

Armhole depth.
From the point P down we put off the taken measure of the depth of the armhole ( Gpr\u003d 21 cm) and put a point G.

Waistline.
From the point P down, we postpone the taken measurement of the length of the back to the waist (Dst=39 cm) and put a dot T.

Hip line.
from point T down is usually delayed 18 - 19 cm. We will take the average 18,5 see and put an end B.

From points G, T, B and H to the left at a right angle we draw horizontal lines: the depths of the armhole, waist, hips and bottom.

Back width.
From point G to the left, we postpone the measured back width Shs(19.5) plus 0,5 cm (increase in free fit) and put an end to G1:
GG1 \u003d Ws + 0.5 \u003d 19.5 + 0.5 \u003d 20 cm.

Distance to the sideline.
from point G1 to the left we set aside half of the taken measurement of the width of the armhole Shpr (12.5) minus 1 see and point G2:
G1 G2 \u003d Spr: 2 - 1 \u003d (12.5: 2) -1 \u003d 5.25 cm.
from point G2 draw a straight line down and put points at its intersection with the lines of the waist and hips T2 and B1.

Root width.
from point R postpone to the left 1/3 semicircumference of the neck Ssh(19cm) plus 1 cm and put a point P1:
PP1 \u003d 1/3 Ssh +1 = 19:3+1=7,3 cm.

Root height.
From point P1 upwards, we set aside the difference between the measurements of the height of the sprout Wr(41cm) and back length to waist Dst (39cm) and put a point R2:
P1P2 \u003d Vr - Dst \u003d 41 - 39 \u003d 2 cm.
points R And R2 connect with a concave smooth curve. We get the line of the neck of the back (line of the sprout).

Back height.
from point T1 up we postpone the taken measurement of the height of the shoulder of the back WPS(36 cm) and put a dot P.

from point G1 up put off 1/3 segment distance G1P and put a point ABOUT. Compasses from a point ABOUT draw to the left through the point P arc.

Shoulder length.
From the point P2 as from the center, with a radius equal to 15cm(taken measurement of shoulder length Dp (13cm) plus 2cm on the tuck), we draw an arc to the intersection with the previously constructed arc (see Fig. 12). Put a point at the intersection of two arcs P1.
R2 P1 =13+2=15cm.
points R2 And P1 connect.

Connecting the dots P1, O and G2 smooth curve, as shown in Figure 12, we complete the construction back openings.

Back shoulder tuck.
from point R2 left on the line R2 P1 set aside 1/3 of the measured shoulder length Dp and set point B;
P2B=13:3=4.3cm.
Draw a vertical line down from point B 8 cm and put point B1.

from point IN left along the line R2P1 postpone 2 cm and put a point AT 2. From a point IN 1 through a point AT 2 draw a line long 8 cm and put a point AT 3. points V3P1 connect with a straight line and get back shoulder line.

Lateral back line.
from point T2 put aside to the right 2 cm and put a point T3. points T3 And G2 connect.

Waistline shaping.
from point T3 up put off 1 cm and put a point T4, points T4 And T connect with a smooth curve (see Fig. 16).

from point B1 postpone to the left 1/2 C6 (60+3=63 cm) and second bust CrII with an added free fit (54+4=58cm) and put a point B2:
B1, B2 \u003d (63-58): 2 \u003d 2.5 cm. points G4 And B2 connect with a smooth curve.

Back bottom width.
from point H to the left we set aside a value that is equal to the width of the back along the hip line (see the drawing, this is the distance BB2) plus 2-3 cm and put a point H1. points H1 And B2 H1 up put off 1cm and put a point H2. points H2 And H connect with a smooth curve.

Back tuck.
Distance YG1 G3.from point G3 draw a vertical line down and put a dot at the intersection of it with the waistline T5, with a line of hips - a point B3. from point G3 put down 4 cm and put a point AT 4, and from the point B3 up - 3 cm and put a point B4.

Depth of tuck.
from point T5 to the right and to the left along the waist line, lay off along 1 cm and put points T6 And T7 AT 4 And B4(see fig. 20).

Back construction completed.

Before
back hem line HH1 let's continue to the left. from point H1 postpone approximately 45-50 cm and put a point H3. From a point H3 draw a vertical line up. From points G2, T2, B2 draw horizontal lines to the left until they intersect with the vertical. The points of intersection with the vertical line are denoted accordingly G4, T8, B5.

Front width.
from point G4 to the right we postpone the taken measurement of the semicircumference of the chest second CrII with an added free fit (54 + 4) minus the width of the back with an increase (according to the drawing ГГ1 = 20 cm) and minus armhole width (measurement taken 12.5 cm) and put a point G5:
Г4Г5=58-20-12.5=25.5 cm.
Through the dot G5 draw a vertical line down, at the intersection of which with the waist line we put a point T9.

Distance to the sideline. from point G5 to the right, set aside half the width of the armhole Spr(12.5) plus 1 cm and put a point G6:
Г5Г6 \u003d 12.5: 2 + 1 \u003d 7.25 cm.
from point G6 draw a vertical line down and put dots at its intersection with the horizontal lines T10 and B6.

Front height.
from point T8 up we postpone the taken measurement of the length of the front to the waist Dpt (44 cm) and put a point P3

Neck width.
from point P3 draw a horizontal line to the right and put aside on it 1/3 semicircumference of the neck Ssh!(19cm) plus 1 cm and put a point P4:
R3 R4 \u003d 19: 3 + 1 \u003d 7.3 cm.

Neck depth.
from point P3 put down 1/3 semicircumference of the neck Ssh (19cm) plus 1.5 cm and put a point R5:
Р3Р5 \u003d 19: 3 + 1.5 \u003d 7.8 cm.
points R4 And R5 connect a straight line, divide it in half and mark the middle with a dot O1. from point O1 lay down at a right angle 1.25 cm and put a point 02 . points P5, 02 and P4 we connect with a smooth curve and get the line of the neck of the shelf.

Center of the chest.
from point G4 to the right we postpone the taken measurement of the center of the chest CG (11 cm) and put a point G7. points P4 And G7 connect.

Chest height.
from point P4 down, extending the line Р4Г7, we postpone the taken measurement of chest height Vg (29.5 cm) and put a point C.

End of tuck.
Along the same line from the point C up put off 2.5 cm and put a point C 1. At this point, the chest tuck ends.

The size of the tuck solution.
from point C upwards we postpone the taken measurement of the size of the solution of the tuck Vrv (12 cm) and put a point U. From a point C, as from the center, through a point At draw an arc to the right.

Opening of the tuck.
from point At on the drawn arc, we set aside the difference between the measurements of the half-girth of the chest of the second CrII (54cm) and semi-girth of the chest of the first CgI (49cm) and put a point U1.
YU1 \u003d CrII - CrI \u003d 54 - 49 \u003d 5cm This construction can be done using a compass. From a point At, as from the center, radius 5cm draw an arc until it intersects with the previously constructed arc. Mark the point of intersection U1.
through dots C1 and U1 draw a straight line, continuing it up by an amount that is equal to the distance C1R4 and put a point P2:
C1P2 = C1R4.

Front shoulder height.
On a straight line T9G5, extending it upwards, from the point T9 we postpone the taken measurement of the height of the shoulder of the front runway (35 cm) and put a point P3.

Auxiliary armhole point.
from point G5 up put off 1/4 distances G5P3 (4.5 cm) and put a point 03 . Dot 0 3 - check Point. When wetting the sleeve into the armhole, it connects to the mark on the sleeve at the point ABOUT
From a point 0 3 circle through a point P3 draw an arc to the right.

Shoulder length. From a point P2 , as from the center, with a radius equal to the measured shoulder length Dpl, (in our case 13cm) draw an arc to the intersection with the previously constructed arc and put a point P4 . points P4 , 0 3 And
G6 we connect with a smooth curve, thereby completing the construction of the armhole in front .

Lateral front line.
from point T10 postpone to the left 1.5 cm and put a point T11. points G6 and T11 connect with a straight line.

Waistline shaping.
from point T11 up put off 1 cm and put a point T12. points T8 and T12 connect with a smooth curve.

Formation of the lateral line in the thigh area.
from point B6 put aside to the right 1/2 difference between hip measurements Sat with an added free fit (60+3=63 cm) and second bust CrII with an added free fit (54+4=58cm) and put a point B7:
B6 B7 \u003d (63-58): 2 \u003d 2.5 cm.
points T12 and B7 connect with a smooth curve.

Bottom front width.
from point H3 to the right, set aside a value that is equal to the width of the front along the hip line (see the drawing, this is the distance B5B7), plus 2-3 cm and put a point H4. points B7 And H4 connect with a straight line. from point H4 up put off 1 cm and put a point H5.

Front extension.
from point H3 put down 2 cm and put a point H6. points H6 and H5 connect with a smooth curve.

Construction of a tuck.
Distance G7G5 divide in half and put a dot G8. from point G8 down we draw a vertical line, and at the intersection with the lines of the waist and hips we put points T13 and B8. from point G8 put down 6 cm, and from the point B8 up - 2 cm and put points B5 and B9.

Groove depth.
from point T13 right and left put aside 1.25 cm and put points T14 and T15, which we connect with points B5 and B9. (See Fig.42)

Construction completed.
But before you start cutting, do not be too lazy to take a centimeter and check the main measurements again. Pay special attention to the waist circumference, since in this technique, when constructing darts along the waist line, not a calculated value is used, but a constant. If during the check you find significant discrepancies between the figure and the drawing (namely in the waist circumferences), they can be easily eliminated by reducing or increasing the opening of the tucks along the waistline.

This is a pattern drawing for the base of a dress - a guide to creating a wide variety of models. Before proceeding with modeling, it is necessary to check the pattern, “put” it on the figure, and, if necessary, make adjustments. And only after full confidence that everything is in order, you can safely begin to create.

And remember, the road will be mastered by the walking one!

I sincerely wish you success!

Download in one file | turbobit | | |

Don't forget to add to your bookmarks. The bookmark buttons are below.

The rights to this article belong exclusively to the author. Full or partial use of the materials of this article in electronic publications on the Internet is possible only if the following conditions are met:
Author information must be saved. In the title or at the end of the published reprint, the source www.site of the Internet resource "Sewing business master" with a direct, active, visible to the user, not closed from indexing by search engines hyperlink to this article should be indicated.
The publication of texts by newspapers, magazines or other replication outside the Internet is possible only with the written consent of the author.

Developing the theme of building patterns for obese women, we offer another option for building the base of the dress. If in the first version we focused on figures of medium splendor and, as an example, we built a pattern for, then in this section we will pay attention to ladies with more attractive shapes and, as an example, we will build the basis of a dress for size 60 semiadjacent silhouette. This technique, as well as any other, does not dictate any restrictions, but only recommends itself for use in cases where a woman’s chest girth authoritatively declares itself to be 120 centimeters or more.

To build a pattern drawing, you need to take the following measurements:

In order to take measurements more accurately, it is necessary to mark the starting points: the seventh cervical vertebra, which is well defined when the head is tilted, as well as the shoulder line at the base of the neck and at the junction of the arm with the shoulder. Use pins or chalk for this if the woman is dressed. If you need to put a point on the body, use a felt-tip pen, which is easily erased with an alcohol-containing liquid after the end of this procedure.

It’s good if the person you are taking measurements from is wearing a thin dress, or better, only underwear. He, or rather she, since we are talking about a woman, should stand straight, without tension, i.e. maintain your normal posture. That is what I draw your attention to. Because, often a woman, when taking measurements or trying on, especially if she sees her reflection in the mirror, wanting to look slimmer, tightens her stomach, straightens her back, etc. The desire to look better is a good desire, but when taking measurements, it can distort the real state of things. And a well-fitting dress on fitting, in ordinary life, will not be as comfortable as we would like, and as it should be.

Therefore, taking into account the above, turn the client away from the mirror, distract him with a peaceful conversation, tie a string around his waist, mark the starting points and proceed to measurements.

For example, we took measurements corresponding to size 60, and when building, all calculations will be based on the measurements given in the table below.

Be careful, you substitute in all formulas when calculating their values.

The experience of using this technique for constructing patterns suggests that an excellent result is easy to achieve under one condition: you need to accurately and diligently take measurements. It is on this that the outcome of all further work depends.

*Name of measurements and symbols*	cm	*Taking measurements*
Product length (Di)		Measure from the cervical point (seventh cervical vertebra), bringing the centimeter to the waist and to the required length.
Armhole depth (Gpr)		Measure from the seventh cervical vertebra to a horizontal line drawn with a centimeter through the armpits.
Back length to waist (Dst)		Measured from the seventh cervical vertebra to the waist line, taking into account the prominence of the shoulder blades. To do this, a thin ruler can be attached to the protruding points of the shoulder blades, the centimeter tape should pass over the ruler.
Back width (W)		Measure horizontally along the shoulder blades, between the upper corners of the armpits.
Half neck (Ssh)		The measuring tape should run along the base of the neck, behind the seventh cervical vertebrae, in front of the jugular cavity (depression).
Semi-girth of the chest 1st (СгI)		The centimeter tape runs horizontally, behind the protruding points of the shoulder blades, in front above the base of the chest.
Half bust 2nd (CrII)		The centimeter tape runs horizontally behind the protruding points of the shoulder blades, in front along the protruding points of the chest.
Groove opening size (Brv)		Measured vertically. It is removed simultaneously with the measurements of the half-girths of the chest. This is the distance from the base of the chest to its highest point.
Waist (St)		Measure horizontally at the narrowest point.
Half hips (Sat)		Measured horizontally, behind the protruding points of the buttocks, in front, taking into account the bulge of the abdomen.
Root height (Br)		Measure along the back from the shoulder at the base of the neck to the waist line. The measuring tape runs parallel to the spine.
Back shoulder height (Vps)		Measure along the back from the point of articulation of the arm with the shoulder to the waist.
Armhole Width (Spr)		It is measured horizontally under the arm: from the place of articulation of the arm with the body from the back side to the articulation of the arm with the body from the front side. It can be calculated using a ruler located horizontally in the armpit.
Side length (db)		Measure from the back side from the top edge of the ruler located in the armpit to the waist line.
Shoulder length (Dp)		Measure along the shoulder from the base of the neck to the point of articulation of the arm with the shoulder.
Chest Height (Hg)		Measure from the shoulder line at the base of the neck to the protruding point of the chest.
Front Shoulder Height (RH)		Measure from the point of articulation of the arm with the shoulder to the waist.
Front length to waist (Dpt)		Measure from the shoulder at the base of the neck to the waistline.
Center of the chest (Cg)		Measure horizontally between the most protruding points of the chest.
Front Width (W)		Measured horizontally above the base of the chest between the corners of the armpits.
Width of the front at the protruding points of the chest (ShpII) Control measurement		It is measured horizontally between the corners of the armpits at the most protruding points of the chest.
Sleeve length (dr)		It is measured from the point of articulation of the arm with the shoulder to the desired length.
Sleeve length to elbow (DRL)		Measured from the point of articulation of the arm with the shoulder to the elbow.
Arm circumference (Op)		Measured horizontally at the fullest upper part of the arm (at armpit level).
Girth of the wrist (hand) Oz		Measured at the wrist joint, taking into account the bone.
Free fit allowances For a free fit, add 4-5 cm to the measurement of the second half-girth of the chest Cr II, to the measure of the half-girth of the hips Sat - 3 cm and to the measure of the half-girth of the waist St - 2 cm.

DRESS SEMI-FITTING. Size 60

Back .

We draw in the right corner of the prepared sheet of paper a right angle with a vertex at a point R (Fig. 1).
Dress length.
from point R down we put the taken measurement of the length of the dress Di(102 cm) and put a dot H. (Fig. 1).

Fig.1

Armhole depth. from point R put down the taken measure of the depth of the armhole Gpr (23cm) and put a point G.

Fig.2

Back length to waist. from point R down we put the taken measurement of the length of the back to the waist Dst (40cm) and put a point T.

Fig.3

The length of the dress is to the hip line. from point T down is usually delayed 18 - 20cm. We will take the average 19cm and put a dot B. From points G, T, B and N to the left we draw horizontal lines of the depth of the armhole, waist, hips and bottom.

Fig.4

Center back line. from point R postpone to the left 1cm and put a point P1 (back bevel). Line segment WG divide in half and mark the middle with the letter L. points P1 And L T postpone to the left 1.5cm and put a point T1. points G, T1 And B connect with a smooth curve, as shown in Fig.5.

Fig.5

Back width. from point G to the left we postpone the taken measurement of the width of the back Shs plus 0.5 cm (increase in loose fit) and put a point G1:
GG1 \u003d 21 + 0.5 \u003d 21.5 cm.
Through the dot G1 draw a vertical line up and down, put a dot at the intersection with the waistline T2.

Fig.6

Distance to the sideline (to the side seam). from point G1 postpone to the left 1/2 armhole width Spr (14cm) minus 1cm and put a point G2:
G1D2=14:2-1=6cm.
The distance to the sideline may vary, it depends on the figure and style. If the figure is with a protruding belly, then the side line is closer to the back, and if the figure is with protruding buttocks, then closer to the front. And, of course, the side line can be in the middle of the armhole.
from point G2 draw a vertical line down to the line of the hips and put points at the intersection with the lines of the waist and hips T3 And B1.

Fig.7

from point P1 to the left set aside 1/3 of the half-girth of the neck Ssh(21cm) plus 1cm and put a point R2:
Р1Р2=21:3+1=8cm.

Fig.8

from point R2 upward we set aside the difference between the measurements of the height of the sprout Wr(42cm) and back length to waist Dst(40cm) and put a point P3:
Р2Р3=42-40=2cm.
points P3 And P1 connect with a smooth curve.

Fig.9

from point T2 up we postpone the taken measurement of the height of the shoulder of the back UPU (36 With m) and put a point P.

Fig.10

Auxiliary point for the design of the armhole. from point G1 set aside 1/3 of the cut PG1 and put a point ABOUT. From a point ABOUT circle through a point P, draw an arc.

Fig.11

Shoulder length. From a point P3 compass (with a radius equal to the measured shoulder length plus 2.5 cm on the undercut) make a mark on the previously constructed arc and put a point P1:
R3P1\u003d 13.5 + 2.5 \u003d 16 cm.
points P3 And P1 connect with a straight line.

We make out the line of the armhole of the back. points P1, O and G2 fig.12.

Fig.12

Along the line R3P1, oh t points P3 postpone to the left 1/3 taken measurement of the length of the shoulder and put a point IN:
R3B\u003d 13.5: 3 \u003d 4.5 cm.
from point IN down parallel to the line RL draw a straight line of length 9cm and put a point IN 1.

Fig.13

from point IN postpone to the left 2.5cm and put a point AT 2. from point IN 1 through a point AT 2 draw a line long 9cm and put a point AT 3. Point AT 3 connect with dot P1.

Fig.14

from point T3 put aside to the right 2cm and put a point T4, which we connect with a point G2.

Fig.15

from point T4 up put off 1cm and put a point T5. points T5 And T1 connect with a smooth curve.

Fig.16

from point B1 to the left we set aside half the difference between the measurements of the semicircumference of the hips Sat and half-girth of the chest of the second SGII
B1B2= (Sat + 3cm) -(CrII+4 cm):2=65–64: 2 = 0.5 cm. And we make a point B2

points T5, B2 connect with a smooth curve. from point B2 draw a vertical line down and put a dot at the intersection with the bottom line H1. (This is a straight dress). You can slightly expand the bottom of the dress to the bottom. How to do this, see the pattern for size 54 section Back bottom width fig.18.

Fig.17

from point G1 set aside 1/3 of the back width to the right (7cm) and put a point G3(Thisdistance may vary). from point G3 draw a straight line down and at the intersection of it with the lines of the waist and hips, respectively, put points T6 And B3. from point G3 put down 4cm and put a point AT 4, and from the point B3 up - 3cm and put a point B4.

Fig.18

Along the waist line from the point T6 left and right put aside 1cm and put points T7 And T8, which we connect with points AT 4 And B4.

Fig.19

Fig.20

Back construction completed.

From points G2, T3, B1 and H1 to the left we draw horizontal lines: the depths of the armhole, waist, hips and bottom, set aside on them approximately 50 cm and put points accordingly G4, T9, B5 and H2. Draw a vertical line through these points up and down.

Fig.21

from point G4 to the right we set aside the distance that we get as a result of the following calculation: the measurement of the half-girth of the chest of the second SGII(60cm) plus 4cm for a loose fit, minus the width of the back according to the drawing (21.5 cm) and minus the measured armhole width Shpr (14 cm) put a point G5:
G4G5 = 64-21,5- 14=28.5 cm.
Through the dot G5 draw a vertical line down and put a dot at the intersection of it with the waistline T10.
We check the width of the front by measuring the width of the front along the protruding points of the chest (ShnII). The width of the front in the drawing must be greater than the measure taken so that it does not turn out that the product is narrowed.

Fig.22

from point G5 to the right, set aside half of the measurement of the width of the armhole Spr(14cm) plus 1cmAnd put an end G6, from which we draw a vertical line down and at the intersection of it with the lines of the waist and hips we put points T11 And B6.
G5 G6=14:2+1=8cm

Fig.23

from point T9 up we postpone the taken measurement of the length of the front to the waist Dpt (47cm) and put a point P4. from point P4. Draw a horizontal line to the right.

Fig.24

from point P4 put aside to the right 1/3 semicircumference of the neck Ssh (21cm) plus 1 cm and put a point R5:
P4P5 \u003d 21: 3 + 1 \u003d 8 cm.

Fig.25

from point P4 put down 1/3 semicircumference of the neck Ssh (21cm) plus 1.5 cm and put a point R6:
Р4Р6 \u003d 21: 3 + 1.5 \u003d 8.5 cm.
We connect points P5 and P6 with a straight line, divide it in half and mark the middle with a dot O1. from point O1 lay down at a right angle 1.5cm and put a point O2. points P5, O2and R6 connect with a smooth curve and get the neckline.

Fig.26

from point R5 put aside to the right 1/3 measured shoulder length Dpl(13.5) and put the point P7:
Р5Р7 \u003d 13.5: 3 \u003d 4.5 cm.

Fig.27

from point G4 to the right we postpone the taken measurement of the center of the chest CG (12 cm) and put a point G7. points R7 and G7 connect.

Fig.28

from point R7 put down 1cm and put a point P2. points R5 And P2 connect.

Fig.29

From the point P7 down we postpone the taken measurement of the height of the chest Vg (33cm) and put a point C.

Fig.30

from point C up put off 2.5cm and put a point C 1.

Fig.31

from point C upwards we postpone the taken measurement of the size of the solution of the tuck Vr (14cm) and put a point At. From a point C through a point At draw an arc to the right .

Fig.32

from point At along the drawn arc, we postpone the difference between the measurements of the half-girth of the chest of the second CrII (60cm) minus half bust first CrI (53cm) put a point U1 .
YU1= 60 - 53 = 7cm.
This construction is conveniently done using a compass. To do this, we draw an arc from the point Y with a radius of 7 cm to the intersection with the previously constructed arc.
Place a dot at the intersection U1.
From a point C 1 through a point U1 draw a straight line on which we set aside a segment equal to the segment C1P2, and put a point P3:
C1P3 \u003d C1P2.

Fig.33

On a straight line Т10Г5, extending it upwards, we postpone the taken measurement of the height of the front shoulder Runway(35.5) and put a point P4.

Fig.34

from point G5 up put off 1/4 segment G5P4(4.65cm) and put a point O3. Dot O3 is control mark when weaving the sleeves into the armhole. From a point O3 circle through a point P4 draw an arc to the right with a radius O3 P4.

Fig.35

From a point P3 draw an arc with a radius equal to: taken measure of the length of the shoulder Dpl(13.5cm) minus distance R5P2 (4.5cm) to the intersection with the previously constructed arc. Place a dot at the intersection P5.
P3P5=13.5-4.5=9cm.
points P3 And P5 connect straight .

Fig.36

points P5, O3 And G6 connect with a smooth curve as shown in fig.37.
Lateral line. from point T11 postpone to the left 1.5cm and put a point T12. points T12 And G6 connect.

Fig.37

from point T12 up put off 1cm and put a point T13. points T13 And T9 connect with a smooth curve.

Fig.38

from point B6 to the right, set aside half the difference between the measurements of the semicircumference of the hips Sat and half-girth of the chest of the second SGII with free fit allowances:
B6B7= (Sat + 3cm) -(CrII+4 cm):2=65–64: 2 = 0.5 cm, and put a point B7:
points T13 And B7 connect with a smooth curve. from point B7, draw a vertical line down and put a point at the intersection with the bottom line H3. from point H2 put down 2cm and put a point H4. points H4 AndH3 connect with a smooth curve, thus making out the bottom line (This is a straight dress). You can slightly expand the bottom of the dress to the bottom. How to do this, see the section "Width of the bottom of the front" fig.39.

Fig.39

Construction of a notch. Line segment G5G7 divide in half and put a dot G8, from which we draw a straight line down and put points at the intersection with horizontal lines T14 and B8. from point G8 put down 6cm and from the point B8 up - 3 cm and put points AT 5 And B9.
from point T14 right and left put aside 1.25cm and put points T15 And T16, which we connect with points AT 5 And B9.

Fig.40

For full figures, starting from the 60th size and above, it is necessary to draw on the pattern deflection (retraction) line. For this, from the point B5 postpone to the left 1-1.5 cm (depending on the bulge of the abdomen) and put a point B10. points R6 And B10 we connect a straight line, extending it to the bottom line. The line drawn is the middle of the front.

Fig.41

Construction completed. But before you start cutting, do not be too lazy to take a centimeter and check the main measurements again. Pay special attention to the waist circumference, since in this technique, when constructing darts along the waist line, not a calculated value is used, but a constant. If during the check you find significant discrepancies between the figure and the drawing (exactly in waist circumference), they are easy to eliminate by reducing or increasing the opening of the tucks along the waist line.

Fig.42

This is a pattern drawing of the base of the dress - the basis for creating a wide variety of models. Before proceeding with modeling, it is necessary to check the pattern, “put” it on the figure, and, if necessary, make adjustments. And only after full confidence that everything is in order, you can safely begin to create.

I sincerely wish you success!

Download in one file | shareflare | | |

Don't forget to add to your bookmarks. The bookmark buttons are below.