Sew an elegant dress for a girl of 6 years. Basic dress pattern for a teenage girl. Pattern of a dress for a girl: a master class

Without complex drawings and intricate calculations, you can sew simple everyday or elegant dresses for special occasions for your daughter at least every day. If you didn’t know about it yet, then simple tailoring options have been collected for you. Experienced craftswomen will also like them.

Simple for girls for 1-3 years

With just one pattern of a one-piece dress for a girl, you can sew many different models.

The model shown below is lined and fastens at the shoulders with buttons. It can be sewn from any thin or dense fabric.

Pattern

You can find a suitable pattern for a one-piece dress in magazines, or you can make it yourself by taking a T-shirt or blouse that fits well on a girl as a template.

How does this happen?

  • Take a large piece of paper or a roll of wallpaper.
  • After spreading the paper, lay out the T-shirt and circle the neck and armholes. Next, make a flare in the form of a trapezoid and round the bottom. It is not scary if the item you have chosen has a high waist or a strong flare. Outline the model, and then remove the excess and finish the necessary, adjust the depth of the armhole and neck. The main thing is that the shoulder bevels, chest width and armhole height are already there.
  • When drawing, the pattern may turn out to be asymmetric. This is not scary, because one half is taken for cutting, naturally the best.
  • If you are circling a blouse with sleeves, then go through the armhole with a needle. Traces will remain on paper and you can beautifully connect them with a pencil. In the same way, you can make a separate sleeve pattern.

Cutting and sewing

  1. Open the front and back of the lining fabric.
  2. Circle the cut parts on the main fabric and cut out.
  3. Sew along the side seams of the front and back of the lining and main fabric.
  4. Match the tops of the two fabrics and secure with pins.
  5. Sew and trim the edges.
  6. Turn inside out and smooth out the seams.

  1. Wrap the edges of the hem of the dress inside, turn the dress inside out and sew, leaving about 5 cm for turning inside out again.
  2. After turning the dress inside out, fold the edges inward in an unsewn hole, smooth them and stitch them.
  3. Lay a line along the upper cuts of the dress.

On the shoulders of the front, mark the place for sewing on the buttons and holes for the buttonholes. Then make loops and sew on the buttons covered with the main fabric.

Summer sundress without a pattern

To sew such a cute sundress, you don’t need a pattern at all and you don’t need to trace anything either, so a beginner in sewing can handle the dress. This model is suitable for a girl of any age and physique, since the width and length are made at your discretion.

  • To begin with, we need to measure the volume of the girl’s chest and determine the length of the sundress. Multiply the volume by 1.5 or 2 to form beautiful folds and not press on the chest area. The length is measured from the armhole, plus 1.5 cm is added to it for the top edge and 4 cm for the bottom hem.
  • Cut out the rectangle, fold it in half face inward and sew along the side.
  • Make a hem at the top and hem. The edges can be finished with a zigzag stitch.
  • Sew 5-10 rows on the dress with a zigzag stitch with an elastic band, or by wrapping an elastic band around the bobbin.
  • Make 2 straps 90 cm long from a contrasting fabric and stitch to the front.
  • From the same fabric as the sundress, make 2 loop strips 5x25 cm and stitch to the back.
  • Pull the straps through the loops and tie into a bow.

Baptismal

While still very young, children are pure and innocent, and very similar to angels, especially during such a solemn ceremony, because white robes maximize this effect.

Baptismal dresses usually have a simple cut, so they are sewn quickly. So let's get started.

bodice

Make a top pattern using any method convenient for you. There will be a button closure on the back, so add a few inches for the placket.

  • Cut out the satin and lining pieces, then sew the front and back in each fabric.
  • Stitch the satin top and lining fabric together at the neckline, folded facing inward. To keep the edges from fraying, process them with a zigzag stitch.
  • Turn the bodice inside out and iron.

Sleeves

  • Make a sleeve pattern and open them.
  • Gather a little at the bottom and at the top.
  • Cut out 2 bands for edging the bottom of the sleeves. Their length is equal to the length of the bottom of the sleeve, and make the width arbitrary, given that it will fold in half.
  • Sew the strips on one side, then fold over and sew on the other side.
  • Sew in the sleeves and iron the seams.
  • On the back, make loops or sew Velcro.

Skirt

The skirt will consist of 3 layers:

  • Lower. From the lining fabric, cut out a rectangle of the same width as the bottom of the bodice, but shorter in length by 5-6 cm from the main length.
  • Average. From satin fabric, cut out a rectangle with a width equal to two widths of the lower edge of the bodice. That is, if the bottom of the front and back is 46 cm, then the width of the rectangle will be 92-100 cm. Make the length as you wish.
  • Upper. The width of the second rectangle will be 2 times larger, that is, 184-200 cm and make the length a couple of centimeters shorter.

Sew each of the rectangles along the side seam. Work the top in a zigzag, and then pick it up to the desired size.

Fold all layers together and stitch, then sew to the top.

Fold the hem of the skirts.

Make flowers from strips of fabric.

elegant

Girls have no less than adults reasons to wear a smart dress. Therefore, we offer to sew a romantic model with frills.

Calculations

  1. The top frill should cover the stitching seam of the next tier, so make the lining parts 2-4 cm smaller than the parts from the main fabric.
  2. To make the skirt voluminous and flared, increase the length of the lining by 1.5 times, and the frills by 2.
  3. If the volume of the top is 60 cm, then the length of the first tier of the lining should be 90 cm, and the frills - 120 cm.
  4. The second tier and subsequent ones are calculated based on the size of the previous ones. That is, the length of the lining of the second tier is 135 cm, and the frills are 240 cm. The third is 202 cm for the lining and 360 cm for the frill.

If the fabric is dense, then the bottom lining is not needed.

Sewing

The top in the dress is ordinary, so cutting and sewing it, we will make a belt.

You will need a stripe of a contrasting color 13 cm wide and as long as the volume of the top. The strip, folded in half lengthwise, stitch to the bottom of the top.

In ruffles, hem the bottom edges with a narrow hem, and gather the top edges to the desired length.

In the linings, also gather the top edges. Then arrange all the details in pairs, so it will be more convenient to assemble the dress.

Stepping back 1.5 cm from the edge of the back, since a hidden zipper will be sewn in there, pin the frill with pins.

Put the first tier of the lining with the front side on the frill and pin it off with pins, while making sure that its sides coincide with the edges of the back, that is, there should be no indents. Sew through all layers.

Sew in the zipper, pinning it to the top and lining, while the frill is not sewn on.

For a nice looking lining, turn it inside out and sew very close to the zipper using the matching foot.

We sew the second tier. Close the rectangles from both fabrics into circles. Then pin the frill to the lining from the 1st tier, and put the second lining on top of it and sew together.

Sew the third in the same way.

Hello. I spread the size range from 80 to 152 cm of dress patterns for girls. Dress of a free cut, with a sleeve.

The pattern is like this.

Simple cut dress. Sleeve pattern with a fold, the same line for front and back.

The neck is high, such to which the collar is sewn. If there is no collar, the neck should be deepened and expanded.

Despite the fact that the dimensions are given up to a height of 152 cm, the patterns are designed for undeveloped children's figures.

The sleeve, of course, can not be sewn.

Dress length to the knee.

Patterns:

Age / Height / BustPattern
1 year / 80 cm / 50 cmDownload
1.5 years / 86 cm / 52 cmDownload
2 years / 92 cm / 54 cmDownload
3 years / 98 cm / 55 cmDownload
4 years / 104 cm / 57 cmDownload
5 years / 110 cm / 59 cmDownload
6 years / 116 cm / 61 cmDownload
7 years / 122 cm / 63 cmDownload
8 years / 128 cm / 66 cmDownload
9 years / 134 cm / 69 cmDownload
10 years / 140 cm / 72 cmDownload
11 years / 146 cm / 75 cmDownload
12 years / 152 cm / 78 cmDownload

The second pattern is built according to the system of the Müllers. According to German accuracy, it carries the display of anatomical features. In general, this pattern is for fans of the German pattern building system and not for beginners.

You can use the tuck on the back armhole for a good fit, or you can ignore it.

Pattern in PDF file in full size. When printing, set the scale to 100%. After printing, you need to glue the sheets side by side, without overlapping the sheets and without cutting the margins.

Patterns are given without seam allowances.

Patterns:

Age / Height / Og / About / LengthPattern
1 year / 80 cm / 54 cm / 57 cm / 38 cmDownload
1.5 years / 86 cm / 55 cm / 58.5 cm / 41 cmDownload
2 years / 92 cm / 56 cm / 60 cm / 44 cmDownload
3 years / 98 cm / 57 cm / 61.5 cm / 47 cmDownload
4 years / 104 cm / 58 cm / 63 cm / 50 cmDownload
5 years / 110 cm / 59 cm / 64.5 cm / 53 cmDownload
6 years / 116 cm / 60 cm / 66 cm / 56 cmDownload
7 years / 122 cm / 62 cm / 68 cm / 60 cmDownload
9 years / 134 cm / 66 cm / 72 cm / 68 cmDownload
10 years / 140 cm / 68 cm / 74 cm / 72 cmDownload

You can decorate the dress with a collar and lace

shuttlecocks

make the dress layered.

I also collected several options for modeling patterns: how to modify a dress.

You can cut off the skirt and make the assembly. The width of the skirt is doubled.

My dear seamstresses! I'm glad to welcome you))).

What could be more beautiful than summer time, greenery, warmth, sun!,. Summer is the most fertile time for sewing masterpieces, because the variety of ideas and fabrics simply conquers the imagination, and you can even sew a dress from a scarf, just wrapping it around you ...

Today we will sew a dress, of course, not from a scarf, but the idea is still as simple as possible.

We will sew a light linen dress for a girl without a pattern.

Such a dress has only two parts, the short sleeve is cut out in one piece with the main part of the dress, so there are four seams - two shoulder and two side - and the dress is ready, all that remains is to process the cuts.

How to choose fabric for a summer dress?

At present, the choice of fabric can rather be a problem due to its diversity, since there are a lot of fabrics, and how to decide?

So let's look at those factors that are fundamentally important.

  1. Firstly, the fabric must breathe (it's summer!), Therefore, we choose natural fabrics - linen, cotton, silk.
  2. Secondly, the dress should not wrinkle much, for this reason it is desirable to contain a small synthetic process in natural fabric.
  3. And, of course, whoever loves it, but I always prefer stretchy fabric to non-stretchy, it is more comfortable to wear, it is more convenient to wear it, it looks better on the figure, it is more flexible.

Considering all of the above, I will take stretch linen for this children's dress - it will breathe and sit well.

  • School of fashion designers in Moscow here - http://xn--e1aialfecu4d.xn--p1ai/praktika-sew.ru/

How to sew a dress without a pattern for a girl?

I want to once again draw your attention to the fact that I have an amateur blog, and I always focus on making the process of creating a thing as simple as possible.

What does it mean?

Everything that can be simplified, I simplify. A clear construction of a pattern where this can be avoided is a waste of time and effort.

Our children grow up so fast that if you make patterns on them, you will have to make them very often. For an adult, it is acceptable to build a base pattern once and then sew a bunch of dresses and other clothes on it, if you don’t get better.

With children, this number does not work: either we build anew all the time, or we adapt. Of course, the second option suits me.

What are we doing? We take our favorite dress, similar to the one we want to sew, and we will circle it directly on the fabric, making some adjustments.

See also about tailoring WITHOUT patterns:

  • Sew a dress from jersey oil with your own hands without a pattern

We wash and iron the linen fabric before use, the share thread should go vertically to the product, on the dress - from top to bottom.

I want to sew a dress not with a square neckline, but with a round one, so I will round the neckline, the sleeves are one-piece with the main part, we adjust the length as desired, so we outline the dress, taking into account centimeter allowances.

Cut out two parts - front and back:

Now we sew them along the shoulder and side seams:

The next step can be done before stitching the side seams. Now you need to process the cuts of the sleeves with an oblique trim. To do this, cut out a strip of fabric 2 cm wide, length = two sections of the sleeve.

We visually divide the long strip into 4 longitudinal parts, it turns out that the width of the allowance is 0.5 cm. We sew a strip of fabric to the cut of the sleeve, folding it face to face:

Then we turn the cut of the oblique inlay by 0.5 cm and fix it with a machine stitch for convenience:

Now we tuck the stitched section of the oblique inlay onto the wrong side of the sleeve and sew it with a straight line along the front side of the sleeve into the split of the seam or at a distance of 1 mm from the junction of the inlay and the sleeve.

Now we process the bottom of the dress with a double hem. We turn it 0.5 cm to the wrong side, sew it with a straight stitch to fix it:

Then we turn it over again and stitch it, so the raw cut along the bottom of the dress will be hidden.

And I will tell you the main points in a nutshell.

We cut a strip of fabric 2.5-3 cm along the oblique, i.e. diagonally relative to the shared thread, such an inlay will stretch well, like an elastic band, and there will be no folds of fabric on the neck.

We sew an oblique trim on the front side of the neck, the trim must be held with a slight stretch relative to the neck fabric, the cut of the neck should not be stretched in any way, only the trim should be stretched. Then it will be perfect.

Building a basic dress pattern

To build a basic dress pattern for a girl, you need to take measurements. We use measurements of the 40th size, but when building a pattern, you will use the measurements taken by you.

Measure………………………………………………Girth…………Semi-girth

1. Bust…………………………………..80 cm…..………40 cm

2. Girth above the chest……………….…..…..76 cm……..….…38 cm

3. Hips……………………………….…84 cm…….….…42 cm

4. Distance between high
chest points…………………………….….……16 cm

5. Length back to waist………………….33cm

6. Front length to waist………….…….37cm

7. Shoulder length………………………………..….10cm

8. Neck girth……………………………………..33 cm………..…16.5 cm

9. Waist………………………………..…68 cm…………….34 cm

10. Hip height …………………….…….…..16 cm

11. Sleeve length……………………………………56 cm

12. The length of the dress (removed along the back from the seventh neck
vertebra to the desired length of the product)………………….…80 cm

IMPORTANT! When constructing basic patterns, it is necessary to make allowances for the freedom of fitting to the measurements taken and the calculated values, so that the future product fits the figure, but at the same time is not narrow and uncomfortable to wear. The amount of increase depends on the desired silhouette of the product.

Chest Increase: 1.5 cm (for an adjacent silhouette), 2-2.5 cm (for a semi-adjacent silhouette), 3-4 cm (for a free silhouette).

Increase in armhole depth: 0.5 cm (for an adjacent silhouette), 1 cm (for a semi-adjacent silhouette), 1.5 cm (for a free silhouette).

Pattern-basis of a dress for a teenage girl

Rice. 1. Basic dress pattern for a teenage girl

Building a pattern grid

Draw a rectangle ABCD.

Dress length. AD \u003d BC \u003d 80 cm - the length of the dress to measure.

Dress width. AB = DC = 43 cm (half circumference of the bust according to the measurements plus 2 cm for freedom of fit for all sizes): 40 + 2 = 42 cm.

Armhole depth. The depth of the armhole should be measured and set aside the measured value from point A down - point G (see).

IMPORTANT! The depth of the armhole can also be calculated using the formula: AG = 1/3 of the half-girth of the chest by measure plus 4 cm for all sizes: 40/3 + 4 = 17.3 cm. If the measured and calculated values ​​\u200b\u200bare slightly different, take the average between them.

From point G to the right, draw a horizontal line until it intersects with the line BC - point G1.

Waistline. From point A, lay down 33 cm - the length of the back to the waist according to the measurements - point T. From point T, draw a horizontal line to the intersection with the line BC - point T1.

Hip line. From point T down, set aside 16 cm (Height of the hips by measure) for all sizes - point L. From point L to the right, draw a horizontal line until it intersects with the line BC - point L1.

Back width. From the point G, set aside the measure 1/2 to the right.

Armhole width. Set aside G2G3 - Armhole width by measure + 0.5 cm (increase in freedom of fitting).

Side line of the dress. Divide the segment G2G3 in half and draw a vertical line down through the resulting point - the line of the side of the dress.

Shelf lift. From point T1, set aside 37 cm upwards (Length of the front to the waist according to the measure) - point W. Draw a horizontal line from point W.

From point G3, draw a straight line upward until it intersects with a horizontal line drawn from point W - point P1 is obtained. The point of intersection with the line AB is denoted by the point P2.

Armhole descent line. Lengthen the lines PG2 and P2G3 down by 0.5-1-1.5 cm, depending on the silhouette (adjacent, semi-adjacent, free) and connect them. In our case, the descent of the armhole is 1 cm for a semi-adjacent silhouette.

Auxiliary lines of the shoulder and armholes. Divide lines PG2 and P2G3 into 4 equal parts - auxiliary points for constructing an armhole have been obtained.

Building a back pattern

Dress neckline. Set aside 6 cm from point A to the right (1/3 of the half-girth of the neck according to the measurements plus 0.5 cm for all sizes): 16.5 / 3 + 0.5 cm = 6 cm. From point 6 set aside 2 cm. Points 2 and And connect with a concave line.

Back shoulder slope. Set aside 1.5 cm from point P down.

Shoulder line. From point 2 (neck) through point 1.5 (shoulder slope), draw a shoulder line 11 cm long (shoulder length by measure + 1 cm).

Armhole line. From point 1, dividing the angle in half, set aside 3 cm. Draw the armhole line of the back from point 11 through the middle point of dividing the line PG2, point 3 and G4.

The line of the side seam of the dress. Set aside 2 cm from point T2 to the left. Draw the side seam line through points G4, 2, L2 until it intersects with the DC line. Draw the line of the side according to the pattern slightly arching in the thigh area.

Building a front pattern

Front neckline. Set aside 6 cm from the W point to the left (1/3 of the half-girth of the neck according to the measurements plus 0.5 cm for all sizes): 16.5 / 3 + 0.5 = 6 cm. Set aside 6.5 cm (1 / 3 half-circumferences of the neck according to the measurements plus 1 cm for all sizes): 16.5 / 3 + 1 \u003d 6.5 cm. Connect points 6 and 6.5 with a dotted line, divide it in half and draw a line 6 cm long through the division point. Points 6, 6 and 6.5 connect according to the pattern.

Shoulder length to chest tuck. Set aside 3 cm from point 6 to the left, then set aside 0.5 cm from point 3 down. Connect points 0.5 and 6. Set aside 8 cm from point G1 to the left (1/2 the distance between the high points of the chest by measure). Connect points 8 and 0.5.

Chest tuck. Divide the right side of the tuck from point 0.5 to point 8 in half and set aside 2 cm to the left from the division point (the difference between the half-girth of the chest and the half-girth above the chest): 40-38 \u003d 2 cm. The left side of the tuck is carried out with a length equal to the right side of the tuck - point P3.

Shoulder length from chest tuck to armhole. Connect point P3 with a dotted line to the upper division point of PG2 (patterns for the back of the dress). Set aside 7 cm along the dotted line to the left - the shoulder length according to the measure minus 3 cm (the length of the shoulder to the chest tuck for all sizes): 10-3 \u003d 7 cm. Connect point 7 with a dotted line with the lower dividing point P2G3. Set aside 1 cm from point 7 down. Connect points 1 and P3.

The line of the armhole in front of the dress. Divide the dotted line from point 1 to the lower division point P2G3 in half and set aside 1 cm from the division point to the right.

From point 1 (lower right corner), dividing the corner in half, set aside 2 cm. Draw the line of the armhole in front of the dress through points 1, 1, the lower division point P2G3, point 2 and G4.

The line of the side seam of the front half of the dress. Set aside 2 cm from point T2 to the right. Draw the side seam line through points G4, 2, L2 until it intersects with the DC line. Draw the side line according to the pattern, slightly arching in the thigh area.

Calculation of traveling tucks

The excess volume that needs to be removed in the darts at the waist is calculated as follows:

Bust minus waist = 40-34 = 6 cm. 1/2 values ​​\u200b\u200bare removed into the side tucks 6/2 \u003d 3 cm (1.5 cm each on the back and front).

1/4 value - in the tuck in the back and 1/4 - in the tuck in the front. For additional fitting, you can make a second tuck at the waist in front with a depth of 1 cm.

A tuck at the front waistline. From point 8 (the center of the chest), lower the perpendicular down to the line of the hips. Set aside the waist to the right and to the left by 0.75 cm. Draw a tuck, not reaching 4-5 cm to the armhole line and 2 cm to the hip line.

Side tuck at the front waistline. Divide the distance from the first tuck to the side in half and set aside 0.5 cm to the right and left from the dividing point. To fit the dress a little more at the waist, you can increase the side tuck solution and set aside 1 cm (1 cm is taken from the increase in freedom of fitting) . Draw a tuck as shown in the drawing.

A tuck at the waistline of the back. Divide the distance along the back waist line in half and draw a tuck 1.5 cm deep, the upper point of which does not reach the GG1 line by 2 cm, the lower point lies on the hip line.

IMPORTANT! If the half-circumference of the hips by the measure is greater than the half-circumference of the chest by the measure, the difference is calculated and added 1/2 along the line of the hips.

Do you want to make an elegant dress for a girl with your own hands? It can be sewn or knitted or crocheted. The article contains simple options that even a beginner can handle. Choose models, read comments. Make outfits for your little fashionista.

Advantages of self-production

Does your princess like to spin in front of the mirror? Does she like to wear beautiful and original things? Please your daughter with a gift of your own production. An elegant dress for a girl with your own hands can be sewn or knitted. Both options have the following advantages compared to buying a finished item:

  • made exactly to size;
  • have an individual design (your daughter will not be in the same outfit with another girl);
  • both of you like it, as the model was chosen jointly from the pictures and tried on during the creation process.

How to make dresses: which one to choose

If we compare the two manufacturing methods with each other, tailoring an outfit has several advantages over knitting. They are the following:

  • takes less time;
  • allows you to get a beautiful thing using a simple pattern at the expense of expensive and spectacular material;
  • you can guess in advance how the product will look on the girl by attaching the fabric to the figure or even wrapping the child in the material;
  • allows you to create a spectacular in the form of a ball or evening option.

If you want to make a light beautiful complete with a panama hat and a handbag, and also have the patience to count the loops and pattern, feel free to choose the crochet method.

Tools and materials

When you have decided on the method of making things, start looking for a specific model and buy everything you need to create it. In the case of crocheting, you will need the tool itself, yarn and a pattern. For tailoring, you need much more:

  • pattern;
  • fabric for dress;
  • material for a petticoat, such as tulle (required in a lush version);
  • regilin and corset tape to stiffen the seams and bottom;
  • pins;
  • tailor's chalk;
  • scissors;
  • needle and thread;
  • sewing machine.

The list can be both large and small, because children's dresses for girls, elegant or casual, are sewn in different ways. Schemes and technologies are used both the simplest in the form of one-piece models, and very complex ones.

Decoration methods

An elegant dress for a girl with your own hands can be sewn using the most

Beauty will be created by the material from which the thing is made, and the decor. You can add the following details to the product:

  • frills on a skirt or top;

  • fabric flowers;
  • lace;
  • original belt;
  • bows;
  • beads and beads;
  • satin ribbon embellishments.

A set with a handbag and a headband or hair clip made of the same fabric will look stylish and original.

How to sew an elegant dress for a girl with your own hands?

Regardless of which model you will make, the general scheme of work is as follows:

In each specific model, there may be other specific steps, for example, making a petticoat, fixing regilin or corset tape, making darts, frills.

How to take measurements?

Children's dresses for girls are elegant, as well as everyday ones, are sewn in accordance with the size of a particular child. This is the advantage of custom manufacturing. The main thing is to correctly determine all the values ​​​​by which you will build a pattern or adjust the finished template.

So, you will need to know:

  • breast size;
  • waist
  • hip girth;
  • the height of the dress from the shoulder line to the desired length (to the floor, below the knee, etc.)

Using these parameters, you can easily build a simple pattern-template, which can then be improved in accordance with the selected model.

How to make frills?

Elegant dresses for girls (photos below) are made according to simple patterns.

Their beauty lies in the use of a large number of ruffles both to finish the bottom edge and to form the skirt itself.

It is easy to make such decor. The scheme of work will be as follows:

How to sew a fluffy dress?

The frills mentioned in the previous section create relief, decor and at the same time add volume to the dress.

However, it takes a lot of time and patience to make a large number of layers with frills. There is another option, how to make an elegant dress for a girl.

Lush and at the same time airy, it will look spectacular on any figure.

To create such a model, you will need the following:

  1. Make a certain pattern for the skirt.
  2. Sew a petticoat, preferably with regilin.

As for the template, you can also take it ready-made or build it yourself. The figure below shows a pattern where the front part is made as one piece. In this case, the skirt will have an easy assembly.

The second way to make a lush hem

To get a wavy surface, you will have to cut out the corresponding part, which is called a sun skirt.

The direction is indicated on the workpiece. It is not difficult to build such a template according to your size. This can be done with a stick with a thread tied to the upper end with a writing instrument (pencil for paper, chalk for fabric).

The paper template is applied to the fold line. The detail is cut along the oblique. As a result, you should get a circle with an inner hole with a diameter corresponding to the waist line.

The petticoat can be made according to the same pattern or another. As you can see in the diagram above, fluffy elegant long dresses for girls can be made from several additional layers of petticoats. They are connected to each other and the base. If, for example, tulle is used for them, the outer layer may be from a different material or from the same.

To obtain a shape-holding edge, regilin is used. It stiffens the seams and allows you to get beautiful waves at the hem. You can process the edges but the effect will be somewhat different.

How to choose the right model?

So, you have seen how different elegant dresses are. For teenage girls, they can be both lush, with frills, and straight. It is important here that the style fits the figure and is liked by the schoolgirl herself. For thin ones, any options are suitable, for plump ones it is better to choose those that make wide hips invisible and do not focus on the waist. Little girls will do just about anything.

If you are going to sew with your own hands, measure the desires of the child with your experience and capabilities. If you are new to this business, take the simplest patterns. It is better to use additional decor. It's always easier to make it. And also do not forget that there is another equally interesting alternative to tailoring - dressy for girls. They may not be suitable for a graduation or some too solemn formal event, but for a family celebration, a visit or a summer holiday on the street, they will be just right.

Crocheted elegant dress for girls

Entire sets look very cute and beautiful when panama hats and handbags are made from the same yarn.

Summer dress with straps is made of two parts. The knitting patterns for each are shown below.

After both blanks of the product are completed, you need to connect them into one.

An elegant crochet dress for a girl can be crocheted according to the second pattern, which is shown below.

In this version, there are even different ways of decorating the cutout. The manufacturing technology is the same as in the previous case. Here are the front and back detail diagrams. They are knitted in two parts, for which you can take yarn of different shades. It will look more interesting and spectacular.

As a result, you will get a product, as in the next photo.

You saw a lot of ideas and ways to make an elegant dress for a girl with your own hands. Choose your favorite model, sew, knit. Please your princess with new outfits.