Sew a sundress with your own hands for a girl of 7 years old. Do-it-yourself sundress pattern for a girl: a master class on creating different models. We sew children's dresses - easy and simple

I think that a sundress for a girl is the most comfortable item in her wardrobe.
In the heat of summer, a light sundress made of thin fabric is simply irreplaceable. In spring and autumn, a sundress is convenient because you can wear either a T-shirt for warm weather or a turtleneck for cool weather under it.
And in winter, a sundress made of warm fabric perfectly warms and does not hinder movement.
The sundress has long been the standard for a convenient and practical school uniform for girls.
There are a lot of options for sundresses. You can't tell everyone.
Here are summer models that will suit any girl.
Models of sundresses are very simple, you can sew them with your own hands without much effort. It remains only to choose!

Summer dress for a girl with straps

This sundress is suitable for a little girl, from 2 to 5 years. You will need a very small piece of light fabric. Suitable satin, linen or cotton.

Now in fabric stores there is a huge selection of all kinds of summer fabrics. You can easily choose the color of your choice.

Measure the length of the sundress from the estimated top edge of the breast to the bottom of the skirt and add 15 cm for allowances and piping. You get the length that you need to sew a sundress.

A sundress can be sewn with a frill along the bottom, as in the photo, or without a frill.

To make a sarafan pattern, use the diagram below as a sample.
Measure sundress length(excluding straps) and chest width.

If you are going to sew a sundress without a bottom frill, leave the length as it is.
If you liked the option of a sundress with a flounce, then we shorten the length of the pattern by the width of the flounce.

We divide the chest width into 4 parts and add 2-3 cm. We get the width of the pattern of each shelf along the chest line.
The height of the breast is approximately 8-10 cm. The front and back shelves are almost the same. The difference is only in the circumference of the armhole. On the back shelf, the armhole is flatter than on the front shelf.
You can make a pattern on paper, cut it out and then cut it out. Or you can cut out a sundress by marking directly on the fabric. Just don't forget the seam allowances.

Scheme of a sundress pattern for a girl

The layout of the pattern of a children's sundress on the fabric

You should get:

back - 1 piece
facing the top of the back - 1 piece
before - 1 piece
turning the top of the front shelf - 1 piece
strap - 2 parts
shuttlecock - 1-2 parts (the length of the shuttlecock is 1.5-2 times wider than the bottom of the sundress)

To make the sundress beautiful not only from the outside, but also from the inside, I recommend immediately processing all the edges of the details with a zigzag seam or using an overlock.

So, to sew a sundress you need:

Fold each strap lengthwise in half right side in and stitch.
Turn out the straps of the sundress and iron.
As straps, you can use elastic band or tape.
Fold the front and back halves of the sundress right side in and stitch the side seams.
Baste the straps to the shelves, determining and adjusting the place and length of the straps.
Keep in mind that the straps of a sundress are closer together on the back than in the front.
Place the facing along the upper edge of the front and back shelves of the sundress with the front side inward. Run a seam that will also secure the straps.
Sew the side seams of the facing.
Turn the facing inside out, iron and topstitch to the edge.
At a distance of 2-3 cm from the edge, very carefully lay another line that will secure the facing along the bottom edge.
Carefully process the bottom of the sundress with a seam in the hem.
If you are sewing a sundress with a flounce along the bottom edge, then you need:
- Sew the side sections of the shuttlecock.
- Finish the bottom edge of the frill with a hem seam.
- Gather the top edge of the flounce and sew to the bottom edge of the sundress.

Summer dress for your daughter is ready!
In addition, you can additionally decorate it with applique, braid or sew on a pocket.

The next model of a sundress for the summer is even easier to sew!

Summer sundress without a pattern

Even if you have never sewed anything, you will still definitely cope with this simple model and sew a summer sundress for your little one in just 20 minutes.

Such a simple sarafan can be sewn from different fabrics. A plain fabric and with a bright print will do.

You will need:
a very small piece of fabric 🙂, with which you can freely wrap your daughter and 1.5 - 2 m of tape for straps.

The sundress consists of two identical parts - front and back.
The sundress should be loose, so the width of each part should be 10-15 cm more than half the girth of your girl's hips.

Moreover, the sundress can be made a little flared.

Scheme for cutting a sundress for a little girl

To sew a sundress you need:

Fold the fabric face inward, mark the length and width of the sundress and mark the armholes with a small piece.
Cut out 2 parts: the back and front of the sundress, not forgetting the seam allowances. If you don't have the right tape for your straps, cut them out of fabric.
Fold the edges of the armholes and sew.
Sew side seams.
Bend the bottom of the sundress, stitch. Optionally, you can add a flounce, border, braid, whatever you like to the bottom of the sundress.
Bend the upper part of the sundress (neck) - make a drawstring.
Pass the ribbon through the drawstring and tie a bow.

Dress for your baby READY!

But for older girls and for teenagers, I recommend sewing a similar sarafan, but you only need to cut it out diagonally.
Diagonal cut or, as it is also called, "oblique cut" will give the sundress a light and flowing silhouette.

Learn more about how to sew a summer sundress without a pattern in 30 minutes in Olga Nikishicheva's video tutorial.

How to sew a sundress without a pattern

Another version of the original sundress for girls

Children's sundress with "wings"

Sewing a summer sundress for a girl, in which lace wings are sewn instead of straps, will not take much time.

You will need:

Some cotton fabric
Lace "Sewing" - about 50 cm
Rubber

To sew a sundress you need:

Measure the length of the sarafan and cut out 2 parts (front and back). Do not forget about seam allowances, drawstring and bottom processing.
Fold the shelves right side in and stitch the side seams.
Sew lace to the front and back shelves as shown in the diagram above.
Finish the edges of the armhole with a seam in the hem. Sew off.
Bend the edge of the neck so that you can insert an elastic band inside. If the width of the lace does not allow this, sew an additional narrow satin ribbon or bias trim on the wrong side. Insert rubber band.
Finish the bottom edge of the sundress. On the bottom of the sundress, you can sew a wide ruffle or lace.

Another summer outfit is ready!

It turned out a light summer dress with lace wings. Looks very romantic. Additionally, a sarafan can be decorated with bows of braid and ribbons.

Summer flared sundress

You can just as easily and quickly sew a children's sundress with a detachable skirt. The skirt can be made either gathered ("Tatyanka"), or "sun".

You will need:

light summer fabric - about 60-70 cm, depending on the age of the girl and the length of the sundress.
threads, braid

To sew a flared sundress you need:

1. Take measurements and mark the pattern. Because the pattern is very simple, you can measure all the measurements at once on the fabric. Use the pattern for a sundress for a girl.

2. All edges of the received parts must be processed.
3. Sew the back seam on the front and skirt.
4. Fold the front and skirt with right side to each other and sew along the waist line. In the process of connecting the upper and lower parts of the sundress, the skirt must be slightly gathered.
5. Turn the bottom edge of the skirt over and sew a seam. You can decorate the edge with braid or lace.
6. Process the top edge of the shelf with a hem seam.
7. Determine the place for the straps and stitch them. As straps, you can use elastic band to match the fabric.

If desired, an appliqué, pocket or ribbon can be sewn to the sundress as a belt.
Update is ready!

Double-sided children's sundress

At first glance, it may seem that a double-sided sundress is an order of magnitude more difficult to sew than a regular sundress, but this is not so. The speed and simplicity of tailoring is its main advantage. And the original straps with knots and the contrast of the front and back sides make the sundress very unusual.

You will need:

Two cuts of spectacular fabrics, 80cm each. One side can be made from a thin jeans (dark blue or light blue). The color of the jeans is beautifully combined with multi-colored cotton.
Harmonious color sewing threads.

Pattern for a double-sided sundress is presented in three sizes:

86/92 (1.5-2 years)
98/104 (3-4 years)
110/116 (5-6 years old)

Seam allowances of 1 cm are included.

Pattern for a double-sided children's sundress

To sew a double-sided sundress you need:

Transfer the pattern to paper (1 cell = 1 cm) and cut out the details.
Cut out the front and back of the sundress from the fabric A and fabrics B. There will be 4 parts in total. Also cut out details for pockets, if necessary. (Let me remind you: seam allowances, in the amount of 1 cm are taken into account.)
Finish all cuts and the hem of the dress with a zigzag stitch or overlock stitch.
Sew a pocket or appliqué onto the front fabric A piece (optional).
A
Fold the front and back fabric pieces B together, right sides in. Stitch and iron the side seams.
Insert one dress into the other so that they fit right sides together inside, and stitch the dresses together along the armhole line, straps and neckline.
Notch the allowances several times at the neckline and armholes. Allowances at the ends of the straps can be cut off a little.
Turn the resulting double dress right side out and iron all edges.
Topstitch with a straight or decorative stitch along the armhole, straps and neckline, not too close to the edge.
Hem the hem of each sundress. On one side of the sundress, you can sew cotton lace, decorative ribbon or braid.

Hooray! Sundress for daughter READY!

I really hope that the presented models will soon be on your girls. Submit a photo!
For those who are just thinking about learning how to quickly sew simple and cute little things for their children, I highly recommend getting acquainted with the Online Sewing School for Moms

don't forget to look.

How often does it happen that the heart of a mother-needlewoman shrinks at the sight of a fabric with a funny children's pattern, asking to become a daughter's dress? And just as often, a lot of ready-made models leave us indifferent: too many bows, too much lurex, an unsuccessful combination of colors and other “charms” in which you don’t want to see your beloved daughter at all. In order not to torment yourself with unrealizable desires, we offer you to learn how to build a universal dress pattern for a girl with your own hands. Bonus: dress and sundress pattern for different age groups of girls. Having built a basic model, then it is easy to diversify patterns to create stylish children's dresses and sundresses.

Once you have learned how to build a basic dress pattern correctly, you can delight your daughter with new cute styles of dresses every season, changing the pattern to the standards of a growing child.

Building a pattern for creating children's dresses and sundresses

We use a meter, measure the girl and write down the values obtained. Keep in mind that it is very easy to make a mistake with the sizes on small ones, so double-check yourself several times.

In our case, we used sizes for a child of about 5 years old (measurements are given as an example - you measure yourself, even if it seems that the ones we gave fit your girl).

From the cervical vertebra to the hem of the skirt - 56 cm
From the cervical vertebra to the waist - 26 cm
Shoulder length - 9 cm
Half neck - 13.5 cm
Half bust - 30 cm
Sleeve - 36 cm

Now, based on the measurements, we begin to build our pattern. You will need whatman paper or paper of a suitable size.

We draw a rectangle ABCD, where AD=BC=56 cm (dress length).

Width: half-bust and additional 4 cm (the model will be quite free. Can be reduced to 2 cm), for all sizes. It turns out: AB \u003d CD \u003d 34 cm

We draw an armhole . Segment AG = 16 cm (? bust additional 4 cm for all sizes). In numbers: 30 cm / 3 +6 cm = 16 cm

From point G, draw a line at an angle of 90 ° to segment BC - point G? (hence AG \u003d BG? \u003d 16 cm).

We mark the waistline: measure 26 cm from point A, point T (according to our standards - the length of the back). From point T at an angle of 90 ° a straight line is drawn to the right to segment BC - point T? (hence AT \u003d BT? \u003d 26 cm)

Segment GG? divide in half, mark the point G?. Draw a line from it to segment DC, mark point H. Intersection point on segment TT? mark as T?.

We measure the armhole. Its width is? half chest (in our case, from 30 cm) and an additional 2 cm for all sizes. According to the formula: 30 cm / 4 +2 cm \u003d 9.5 cm. From point G? set aside 4.75 cm to the right and left to the segment CD. Points G? and G? From them, draw up straight lines to the segment AB - mark the point P and P?

Lifting the shelf: from points B and P? set aside up 2 cm. Mark points P? and P?, connect with each other. These are the auxiliary lines of the shoulder and armholes. Segment PG? split equally. Segment P? G? divided into three equal segments.

How to make the back of the product.

We start with the neck. From point A to the right, measure 5 cm (? Neck half-girth by measure and additional 0.5 cm for all sizes): 13.5 cm / 3 + 0.5 cm = 5 cm. From this point, measure up 1.5 cm and connect with point A in a slightly concave line (use a template).

Shoulder construction. We note the slope of the shoulder: from the point P down, measure 1.5 cm. From the neck of the back, where we marked 1.5 cm, through the slope of the shoulder (the second point 1.5 cm) we draw a straight line equal to 9 cm, according to our measurements.

Is the back armhole built from point G? bisector, 2.5 cm long (a line dividing the angle in half). We draw a smooth line from point 9, through half of the PG segment? (where we measured it), through point 2.5, to point G?.

From point T? measure 2 cm to the right. We draw the line of the side seam: G? - point 2 - segment CD (not reaching it 1 cm).

We build the bottom for the dress. We divide the segment DH in half and connect it to the side seam line at point 1 with a smooth line.

We build before products.

Calculate? from the half-girth of the neck and add 1 cm for all sizes: 13.5 cm / 3 +1 cm = 5.5 cm

We measure this length from point P? down.

Calculate? from the half-girth of the neck and add 0.5 cm for all sizes: 13.5 cm / 3 + 0.5 cm = 5 cm

We measure this length from point P? to the left.

We connect the resulting points 5.5 and 5 with a concave line.

From point P? lay down 3 cm, noting the slope of the shoulder. Then, from the neck of point 5 towards point 3, we draw a line of length 9 cm (according to our measure).

Is the front armhole built from point G? bisector, 2 cm long (a line dividing the angle in half). We draw a smooth line from point 9, through half of the segment П? Г?, through point 2, to point Г?.

From point T? measure 2 cm to the left. We draw the line of the side seam: G? - point 2 - segment DC (not reaching it 1 cm).

From point T? set aside 2 cm down and connect to point 2 on the side seam line.

We build the bottom for the dress. From point C we extend the segment BC by 2 cm. We connect point 2 with point 1 from the bottom (on the line of the side seam).

We suggest using simple free patterns to consolidate your skills.

Sundress for a fashionista for 3 years:

Elegant dress for a girl 10 years old:

In addition to the models presented on the network, there are many more patterns that you can download to replenish your collection.

Several videos on the topic of the article

We wish you creative success.

Master class on sewing a children's sundress. Today we will tell you how to sew a sundress for a girl with your own hands.

Required materials and tools:

Paper pattern of the base of the bodice of the dress, fabric, hidden zipper, button, threads, scissors, tailor's pins.

Pattern preparation.

To make the sundress easier to sew, and the thing itself turned out to be beautiful and even, it is better to cut out the product using the already proven pattern-base of the bodice of the dress for the girl. On the paper blank on the front and back, we outline a new neck line.

Now imagine where the straps will be. At the same time, it is important that they coincide when combining the patterns of the front and back along the shoulder seam.

The last step in preparing the pattern for the upper part of the sundress is the design of a new armhole line.

Tailoring the top of the sundress.

Using the existing paper base, we cut out two parts for the front and back (one for the lining). We measure the length and width of the strip from the pattern, which will serve as a strap, and also cut it out in duplicate.

Let's make straps. We fold the fabric blank in half and sew along the long side. Then we turn it inside out and smooth it so that the seam is in the middle. It remains only to lay the stabilization line a few millimeters from the long edge.

We connect the straps with the "lining" of the bodice of the sundress. It is advisable at this stage to try on the future product, so that when finished, the straps fit beautifully on the shoulders and shoulder blades of the model girl. Please also note that the seam on the straps at this point should match the right side of the cut lining.

Sew the front and back of the lining along one of the side seams. The other one is left for lightning. Similarly, we sew both parts from the main fabric.

Now we sew the inner and outer parts of the bodice of the sundress, turn the part inside out and, by analogy with the straps, lay a stabilization line along the upper edge.

Sewing a sundress skirt.

To cut out the lower part of this product, no special calculations are necessary. The pattern is a rectangle, the length of which coincides with the length of the future skirt of the product, and the width - with the width of the purchased fabric, but not less than 1.5 girth of the girl's hips.

We sew the rectangle along the only side seam, leaving the area for the zipper unsewn. We lay two straight lines along the upper part of the skirt and gather the fabric until its width is equal to the width of the bodice.

Product assembly.

On the bodice, we smooth the side seam in such a way that a hidden zipper is placed in the formed “pocket”. We sew the main part of the bodice with the skirt, and leave the lining unsewn about 3-4 cm to the future side seam.

We sew in a zipper, smooth the seams.

We bend the bottom of the product.

Tailoring of a belt and a bow.

The pattern and tailoring of a belt for a sundress is not fundamentally different from how the straps are sewn. First, we cut out a rectangle, which we sew along the long side, and after turning it over, we smooth it and sew it a few millimeters from the edge.

To create a bow, cut out a square from the fabric. We smooth its two parallel sides by 0.5 cm, and sew the other two.

We turn the workpiece inside out and manually sew the remaining open edges with hidden stitches. The middle seam should be in the middle.

Now we find the vertical middle of the rectangle and manually tighten along this imaginary line. It turns out a beautiful bow.

We sew it to the edge of the belt, and fasten the button on the back side.

The second part of the button is placed at the second end of the belt. At the same time, the belt itself, so that it holds securely, is best sewn to the sundress in the area of \u200b\u200bthe side seam (without a zipper).

Sundress for the girl is ready!

The final look of the craft. Photo 1.

The final look of the craft. Photo 2.

The final look of the craft. Photo 3.

A sundress can be decorated with a bright and beautiful pattern. Find a drawing that suits the girl. To make the drawing beautiful, the quality of the drawing itself must be good. It is best to print on a cut, and not on a finished sundress. Finding where they print pictures is not a problem. For example, printing on a cut is done.

There is simply a huge assortment of various summer children's clothing, but a sundress is considered the most comfortable outfit for a girl. A sundress is an important part of the wardrobe, and all thanks to its practicality, because such a model can be worn by representatives of different ages. A pattern of a sundress for a girl will allow you to create an outfit with your own hands, which is ideal for a little fashionista.

Choosing a model based on age

A silhouette called a trapezoid is suitable for the smallest. Very often, such models of sundresses are equipped with straps, and you do not need to have special skills to sew them.

Patterns of trapezoidal outfits in front and behind are not much different from each other, so they are very easy to make. The sundress flares out a little at the bottom, and to build the pattern, you need to take measurements of the chest girth to determine the top, as well as choose the length of the outfit. In addition, you need to measure the width of the arms to draw the armhole.

Outfits for older girls are more sophisticated and sophisticated. To make a sundress pattern for a 7-year-old girl special, combine a variety of fabric colors. No need to limit your imagination, because you can create several different sundresses of the same style. A very popular option among little fashionistas is the sun skirt.

Sundresses with a skirt consisting of several panels also look beautiful. This outfit has a festive look. The set of a sundress with Figaro looks interesting. A cape-jacket will make the outfit fashionable and more versatile. The main thing is to use a similar fabric for figaro. For a pattern of a shelf with a back, take any jacket or blouse. Short puff sleeves look great.

Necessary materials:

fabric (its width and length are calculated taking into account the size of the child);
sewing machine;
threads;
paper;
pencil;
ruler;
chalk or dry soap.

Sundress pattern for a girl 10 years old and older:

We transfer the pattern to paper, calculating the length of the lines, taking into account the size of the girl, as well as the product.
Having drawn a pattern, it must be cut out and then attached to the fabric.
All details should be carefully outlined with chalk or a bar of soap (it is better not to use a pen or felt-tip pen for this, because there will be traces that will be very difficult to remove).
It remains to cut out the details and sew them.

We cut out a large rectangle, leaving allowances vertically to hem the bottom edge (although it is better to sheathe the bottom with some kind of lace or ribbon).
Leave an allowance for the drawstring. Its dimensions are affected by the width of the rope or ribbon - if the braid or ribbon is rather thin, you need to add only 5 cm; when it is wide or a twisted cord is used, then 10 cm must be left.
At the same time, we choose the width of the product, taking into account that if it is wide, then there will be a lot of assemblies. Pleats look great if the fabric is thin, so they can be used in large quantities. Whereas hard material must be dosed, otherwise the sundress will look like a bell.
We leave allowances for all seams.
We cut out two main details - one will be used for the front, the second - for the back. We mow a few centimeters on the armhole, given the fullness of the baby.
It remains to sew a sundress for the girl with your own hands: transfer the patterns to the fabric, and if everything is fine, sew on a typewriter.

Read also:

Pattern of a school sundress:

According to the measurements taken, prepare the main pattern by drawing the main lines on it.
When making the back, divide the tuck located at the back into two parts. Continue the middle lines to the very bottom until they intersect with the bottom of the dress. The lines of the bottom and waist must be continued by 5 cm. Connect the resulting points with a line, leaving an allowance for assembling the product.
In the middle of the front part, you need to set aside 2 cm from the neck itself. Then draw a line from the obtained point to the neck. Set aside 2 cm from the middle of the front along the waist to the right so that the bodice fastens.
Mark several loops: one is 2 cm lower from the neck, the distance between the rest should be 6 cm.
Continue the darts until they intersect with the bottom of the product.
On the bottom of the skirt itself, you need to set aside 5 cm for allowances.
The sleeve pattern remains unchanged. The length of the cuff should be the circumference of the girl's wrist, to which 2 cm is added.
It turns out a school sundress for a girl: the pattern must be numbered before transferring it to the fabric. Otherwise, the details may be confused.

Variety of options

The pattern of a cut-off dress-sundress along the waist line is suitable for girls with a height of 122-128cm. The skirt is pleated. Zipper in the middle back seam. Using this pattern, you can sew not only a strict school sundress, but also a summer dress for relaxing, choosing bright fabrics.

The pattern is calculated chest girth 60-64cm - this is the age of 7-8 years. Age guidelines are rather “slippery”, since children at this age are of different heights and different fatness, so before cutting, take the main measurements: chest and waist, length to the waist and the entire product, and compare with the parameters of the pattern. Correct if necessary

A table of sizes for children's clothing, as well as the ratio of the age, height, chest circumference and weight of the child can be

Choose fabrics depending on the purpose of the sundress dress: preferably natural - these can be plain fabrics or with a small delicate pattern, in a cage, in peas, etc.

Pattern preparation

Print the pattern sheets on the printer and connect them in accordance with the diagram. The scheme is the order in which the pattern sheets are connected. It is printed on the first page.

Be sure to check the scale. On a printed sheet with a depicted square of 10x10 cm, the sides of 10 cm should correspond to exactly 10 centimeters. To do this, in the printer settings, set the print scale of the document to 100% (without scaling).

After gluing the sheets (it is convenient to do this with a glue stick or narrow tape), carefully cut out the details of the pattern.

The pattern is given without seam allowances.

Details of the cut of the sundress dress

Backrest 2 parts
Before the bodice 1 piece with a fold
Side of the front of the bodice 2 parts
The front panel of the skirt 1 piece with a fold
The back panel of the skirt 2 parts
Skirt details are cut according to one pattern

When cutting, do not forget to allow for seam allowances!

Tailoring of a sundress.

The processing of the neck and armholes of the summer version of the sundress dress provides for edging with an oblique trim from the main material, or you can use the finished one. The bodice of a sundress dress for the cool season is recommended to be lined (cut according to the main details). The processing of a sundress dress depends on the material and, if synthetic fibers have an advantage in its composition, then the dress should be completely sewn on the lining and the bodice and lower part.

For those who want to build a pattern for a specific figure of a child according to the measurements taken, we have a detailed