How to fold a paper airplane step by step instructions. How to make an unusual airplane out of paper. Volumetric cardboard craft

Folding a simple airplane out of paper takes 5 minutes. Models of complex design require more experience and a sufficient amount of free time. Having assembly diagrams makes the process much faster and easier.

What paper and materials will you need?

To fold a paper airplane, all you need is paper. The most common stationery paper, A4 format, is suitable. For large models that are planned to be launched outdoors, you can take an A3 sheet. It is not advisable to take a larger size, since launching and planning such an aircraft is problematic.

Paper thickness depends on the aircraft. For light, floating models, classic printer paper or newspaper is suitable. For rigid, gliding aircraft, paper with a density higher than 100 g/m 2 is typical.

Due to the hardness of the material, it is possible to achieve the necessary flight characteristics.

In addition to paper, in rare cases, scissors or glue are additionally used to better secure the model. Beginners can use a long ruler; it helps avoid crooked and asymmetrical bends. If desired, the finished model can be painted in different colors or covered with stickers.

Classic paper airplane model

The classic version of the aircraft model consists of 6 steps:

The model is universal and suitable for launching by both children and adults. This is due to the average flight characteristics – sufficient for moral satisfaction.

Fighter jet

It takes longer to make a fighter jet.

This involves a lot of action during the folding process, but the work itself is not difficult at all:

A fighter jet is capable of flying fast and far when launched correctly. The plane must be thrown forcefully and at a slight angle of up to 50 degrees to the ground.

Military paper plane

Such a fighter flies smoothly and smoothly. To complete it, you need a landscape sheet and a few free minutes.

Performance:

Fold the sheet in half lengthwise to determine the central axis.
Bend the upper corners close to the axial fold.
Turn the sheet over and fold the corners back toward the center line. The result is a narrow and long “nose” of the aircraft.
Straighten the folded top layer of paper from the back side to form a diamond consisting of 2 halves. Fold it in half. Thus, from a rhombus a triangle is obtained with the base at the top.
Fold the workpiece in half with the folded layers facing out. Bend the wings at a distance of 2-3 cm from the axial fold.

The plane folds up quickly enough, the diagram is clear even to a child. It is better to take paper that is not very thick, since the nose of the model is already weighted. In flight, a military aircraft is characterized by smooth and long gliding with a smooth descent.

Paper airplane with propeller

To make an airplane with a propeller, you will need an A4 sheet and a paper square measuring 10x10 cm (for the propeller). The square is cut diagonally, not reaching the center 1 cm from each corner. Secure every second corner obtained with a needle in the center. The resulting propeller is finally attached to the nose of the aircraft.

The paper plane is folded according to the following pattern:

Children will like the plane because it is not like other models.

When launching, special skill is required, otherwise it will not fly. For reliability, the propeller can be glued with superglue after fixing; it is important not to get on the propeller itself, otherwise it will stop rotating.

How to make an unusual plane

Any model that does not look like a classic airplane looks extraordinary and attractive.

This original aircraft resembles a passenger airliner, the assembly diagram is as follows:

You need to make a square from a landscape sheet by cutting off the excess width.
Press two diagonal folds onto the sheet. Fold in half to form a triangle.
Fold the sharp corners towards the center to form a rectangle, then fold in half along the fold. You should end up with a right triangle with a folded base at the bottom and 3 independent corners at the top.
The two outermost free corners are the wings. They must be bent at a distance of 3 cm from the base of the plane.
A tail is formed from the central corner. To do this, you need to make a fold 3 cm wide, which is clamped between the base of the wings. For better fixation, the base is glued with PVA.
The tip of the nose is cut from bottom to top at an angle of 30-40 degrees.

Scheme of how to make a boomerang plane

The boomerang plane is made from a landscape sheet of paper.

The scheme consists of the following steps:

Fold the sheet in half crosswise.
Fold one half in half again and leave folded.
Bend the workpiece in half lengthwise (with the folded section inward). Squeeze well and open the workpiece.
Bend the resulting angles to the center line on both sides.
Fold the resulting “nose” inward along the fold line located on the reverse side.
Fold the workpiece in half and press firmly. Open again.
Form wings. Bend small corners parallel to the fold existing at the edges of the wings.
Fold in half with the small wings folded inward.
Bend the large wings at a distance of 2-3 cm parallel to the entire plane.

The model is for the lazy, because with the right design, no matter how you launch it, it will fly back. Children will really like this paper toy. It should be taken into account that the paper for a boomerang plane needs to be thin and light - then various turns and maneuvers are possible during the flight.

Origami paper airplane

A paper airplane, the design of which involves multiple folds and additions, is also called origami. Or rather, aerogi.

One of the representatives of this type of creativity is the following aircraft:

The landscape sheet is folded in half lengthwise to determine the central axis.
The upper corners are folded close to the central center line on both sides.
The resulting acute angle is bent transversely inward. In this case, it is necessary to retreat 2.5-3 cm further from the previously bent corners.
The workpiece is turned over. The top edge is turned up half a centimeter.
The workpiece is turned over again, and the upper corners are folded towards the central fold.
If everything is done correctly, there should be a small triangle at the bottom, which must be folded upward for additional fixation.
The almost finished plane is folded in half with the folds facing outwards. All folds and folds are pressed well. It's better to do this with a ruler.
The wings are formed in a special way. When they are laid down, the middle of the rear plane of the wing and the angle of the lower, rear base of the aircraft must coincide.
To improve flight qualities, the wings can be bent again by half a centimeter along the edge.

Attention! This model is capable of flying for considerable distances, provided that it is folded correctly.

The bends on the wings must be strictly at right angles, the aircraft itself must be symmetrical and proportional.

How to make a fast paper plane

A fast paper plane is similar in appearance to a fighter, but has wider wings and, accordingly, its design is different.

It develops step by step as follows:

This model flies faster than others due to its design: a narrow and long nose without weight and wide, maneuverable wings. Such characteristics will allow the aircraft to stay in the air longer.

What does it take for an airplane to fly far?

Paper airplanes are conventionally divided into long-flying and long-flying. Models that fly long distances are narrow and dense. Their main feature is their length and center of gravity, which is located closer to the nose of the product.

The layout of a paper airplane should be proportional, with a correctly aligned center. When folding narrow and long models, it is important that the wings are as symmetrical as possible. It is necessary to determine the places of folds in advance and make them even and clear.

Video: paper plane, diagram

How to make a paper airplane that flies far, watch the video:

Making an origami plane:

We present to your attention a selection of paper diagrams of World War II aircraft. These are flying scale models of famous aircraft. Among them there is sure to be an airplane model that you like. Each diagram has a history of the aircraft printed on it, as well as brief gluing instructions. The difficulty level is at the “below average” mark.

In order for you to get a model of an airplane that can fly (flight performance will need to be improved through trial and error - by making the nose of the glider heavier and changing the angles of the wings, etc.) you need to use ordinary office paper in A-4 format.
You can print aircraft diagrams on any printing device. To make the planes look more beautiful, it is better to print the scans on a color printer.
You can cut out the parts with any tool convenient for you - scissors or a paper knife. The main thing is that they are sharp and the details are neat.
There are bend lines on the parts that should be pressed with the back of scissors or any other similar object. This is done to ensure that the bends are perfect.
PVA or a dry glue stick is ideal as glue. In order for the parts to be glued together properly, PVA glue must be applied with a thin brush. Wipe off excess with a napkin or finger.

Paper diagrams of World War II aircraft

This is a scaled-down flying model of the British single-seat fighter Hawker Hurricane, developed in 1934.
Hawker Hurricane fighter
Paper model of the German Junkers JU-87 dive bomber and attack aircraft. This plane is a symbol of the victories of Germany in 1939-1942. The Junkers JU-87 is known for its signature feature - the roar of a siren during a dive.
Junkers attack aircraft JU-87
American Lightning reconnaissance and heavy fighter aircraft, developed in the late 1930s. This aircraft was used by American aviation for reconnaissance, including night reconnaissance, horizontal and dive bombing.
Lightning Heavy Fighter
Model of the English heavy fighter Mosqito. The aircraft's first combat flight took place in 1943. The fighter was successfully used by the Royal Air Force during World War II to carry out targeted strikes.
Mosquito fighter
Another model of an American fighter from World War II is the Airacobra P-39. This aircraft is the most popular because it was supplied by the American authorities to the USSR as assistance in the war with Nazi Germany.
Airacobra P-39
The Thunderbolt P-47 fighter is also a representative of American military aviation. This aircraft is considered the largest single-engine fighter of its time. It was also supplied as aid to the USSR.
Thunderbolt P-47 fighter
Japanese light carrier-based fighter Zero Sen A6M. The aircraft was produced from 1940 to 1945. It had a technical advantage over Allied aircraft until 1942, when the Americans began using the Lightning fighter.
Carrier-based fighter Zero Sen A6M
German single-seat fighter Focke Wulf - FW-190. Due to its versatility, this aircraft was used by the German Luftwaffe as an interceptor, fighter, and escort fighter.

Folding all kinds of airplanes using various papercrafting techniques is one of the most fun ways to spend time with your child. And how many opportunities for creativity! Aircraft can be painted with felt-tip pens and paints, hung from the ceiling in a room, and air wars can be staged. Using the paper origami technique, airplanes turn out nimble, stable and realistic. It turns out that the choice is not limited to one simple model that you mastered in school.

In this article we will figure out how to make origami airplanes, because paper can be used to assemble both elementary and complex types of aircraft.

Before you start making an origami paper airplane, read the following recommendations:

For large crafts, take a thick sheet of paper.
Make small parts from thin sheets.
Use a metal ruler and a utility knife to ensure even cuts and folds.
For gluing, use transparent types of glue.
Monitor the accuracy of the work, maintain symmetry, make bends and cuts even.

Note! Better flight is ensured by a large wing area, and curved wings improve aerodynamic properties. You need to launch the airplane upward at an angle of about 40-45 degrees.

Now you can start creating origami airplanes: paper assembly diagrams are presented below.

Simple options

Let's start making an origami airplane out of paper. The diagram of each model is presented in detail and clearly. Most of the following twelve models can be assembled even by a child, following the instructions step by step or repeating them after an adult. First, practice on basic types of aircraft, then move on to models that require more care and perseverance.

Note! Dotted lines on all diagrams indicate fold lines. You need to fold the sheet along them in order to preliminarily mark the places where further folding of the sheet will be formed.

A glider or arrow is the simplest type of origami paper airplane that flies quite well over short distances. Every child, starting from kindergarten age, can fold a glider.

The first method is a basic glider model with a pointed nose. If you learn how to launch it correctly, it will fly for quite a long time and smoothly.

Blunt Nose Option – The arrow has a good range of gliding through the air.

Complex options

Having gained experience with the previous twelve models, you can turn your attention to origami paper airplanes for tricks of varying degrees of complexity. This is where a real paradise begins for those who like to make complex aircraft.

Below are detailed instructions with pictures:

Take a colored A4 sheet. The thinner the leaf, the higher the flight range.
Form a fold in the center along the long side.
Bend the workpiece in half lengthwise.
Fold and carefully iron one corner.
Repeat the same with the second corner.
Fold the corners in half again and press the folds with the pockets.
Open each corner and fold it inward so that you get two diamond shapes on both sides.
Fold the corners inward, closing the pockets.
Fold the top corners as shown in the picture.
Also turn the corners on the other side.
Open the pockets again by folding the pieces on one side and the other.
Fold the structure along the original fold line.
Draw a line approximately 2.5 cm long from the bottom edge of the sheet.
Bend the two wings along the drawn line.
Draw another line on each wing as shown in the photo.
Bend both wings - these will be the elements of stability of the aircraft.
Make flaps to increase flight range and provide stability to the vertical elements of the wings.

Making a paper airplane that flies well is easy. You need to follow the step-by-step instructions and smooth out all the bend lines well.

Every person has childhood memories associated with making paper airplanes. We loved making them with our own hands and then launching them up
Many children have a craving for creativity. If they make airplanes on their own, this will help develop the baby’s fingers.
The child will learn to concentrate, think creatively and use imagination. For children's, you can arrange a competition between children to see who can make an airplane the fastest.

Important: Working with paper is a pleasure - it is soft and pliable. A model with regular and even curves will be able to fly high and will keep its shape for a long time.

How to make a paper airplane, step by step instructions?

Such a paper “flight machine” can be made from any paper: printed A4, notebook page or even newspaper.

Important: Try to learn how to make simple layouts first, and then move on to complex ones. Kids love to do origami, so they will be happy to help.

So, if your little one comes to you with the question: “how to make an airplane out of paper?”, prepare a small piece of paper and follow the following steps. Step-by-step instruction:

1. Place the paper piece with the smaller side facing you

2. Fold the sheet exactly along the center line and make a mark in the center. There will be a bend, no need to smooth it out

3. Open the piece of paper and fold it so that the top corner touches the center

4. Do all this with another corner of the sheet

5. Open the sheet again. Now fold the corners, but so that they do not touch the center

6. Now fold the smaller corner. It will serve as a holding element for all the corners folded earlier

7. At the last stage, bend the resulting product along the center line - the triangular part will be visible from the outside. Fold the sides towards the center. That's it - the plane is ready

How to make a cool paper airplane?

Cool paper airplane "Glider"

After you have learned how to make classic paper layouts, you can try folding something unusual and complex. The Glider airplane will maneuver high and far.

So, how to make a cool paper airplane? Step-by-step instruction:

1. Take a piece of paper and fold it in half

2. Then open it to its original position and place it with the fold facing up. Fold the corners of the paper inward to create a mark in the middle of the sheet. Now the triangles will be even, and this will help make a layout with good flying qualities

3. Draw a visual line in the center and make a bend in this place. You will get a sharp nose of the product

4. Fold the spout so that it extends a couple of millimeters beyond the edges of the corner bends.

5. Fold the product in the center so that the back side is inside

6. Bend the wings - they can be made small or, conversely, hollow. Experiment with the width as you wish. That's it - the plane is ready

Make a military plane out of paper?

The layout of the “Hawk” model is a little more complicated. But you have already learned how to make simple models, which means you will be able to fold this paper sample.

Step-by-step instructions on how to make a military aircraft out of paper:

1. Prepare a piece of paper and place it on the table with the smaller edge facing you

2. Fold along the center line. Fold the top corner. The top of the paper sheet should coincide with the side. Do the same with the second corner element

3. The piece should look like a cross. Press its side elements to the center line of the paper and iron all the formed lines. Fold the upper right corner so that it is flush with the top of the sheet. There should be 1 centimeter left from the fold to the midline. Repeat the same with the other side

4. The result is “horns” that need to be folded in half, and the excess paper should be folded inside

5. The bottom corner is turned in the opposite direction from you. Make a fold line to the point where the “horns” emerge

6. Fold the airplane in half - it's ready. Paint it with paints and you will get a real military fighter

Important: You can make other models of military aircraft using the drawings presented below.

How to make a light airplane out of paper?

If your child constantly asks to make a paper airplane, teach him to fold it using the origami technique on his own. The diagram below will help you make a light paper airplane.

Tip: Follow the drawn instructions with your child. He will love making these airplanes, especially from colored paper.

How to make a simple paper airplane?

Here is another option for a lightweight model. Many people often wonder: how to make a simple airplane out of paper?

Important: This diagram will help you fold the product in 10 seconds. As a result, you will get a well-flying paper model - simple, fast and interesting!

How to make an airplane with a paper propeller?

To fold such an airplane, you need to prepare a sheet of paper, a paper knife, a pencil, and a needle with a bead at the end. Step-by-step instructions will tell you how to make an airplane with a paper propeller:

1. Take a flat sheet and fold it diagonally twice

2. Open the piece of paper and fold it along the line that will divide the diagonals into two parts. Open the sheet again, raising the corners along the resulting lines

3. Turn the left edge of the corner to the right and bend it. Return it to its original position and bend the right edge upward

4. From the left edge, make a bend again - the bottom should lie on the bend line of the triangle that was made at the previous stage. Bend the edge of the corner behind the resulting part

5. Unfold the right side and bend it towards the center

6. Make another fold towards the center, and tuck the top of the corner inward

7. Bend the right side towards the center, then straighten it again. Turn the left corner over and tuck the bottom edge into the hole on the right piece

8. Bend the resulting product in the center and fold the wings

9. All that remains is to make the propeller: take a sheet of paper measuring 6 cm x 6 cm. Draw it diagonally with a pencil. Make cuts along the drawn lines, not reaching the middle 7 mm

10. Fold the propeller through one corner and secure with a needle and bead

Important: The part may move apart, so glue the corners in the middle or smooth the propeller where it bends

11. Attach the part to the “tail” of the aircraft. The product is ready, you can launch it or give it to a child

How to make a boomerang plane out of paper, diagram?

There is another model of a paper “flying machine” - a boomerang. Imagine a product made by yourself that comes back to you after launch.

The diagram and step-by-step instructions will tell you how to make a boomerang plane out of paper:

1. Fold a piece of paper into four times and press on the corner with your finger

2. Bend one half of the paper cut to the center line and push the corner onto the quarter of the paper

3. Fold the sheet inward from the quarter fold to the top corner. You will get a bend in the form of a triangle. Press your finger along the edge

4. Straighten the triangle, and lifting it, insert your finger between the resulting parts. This is necessary to make sure that the folds are folded perfectly evenly.

5. Turn the product over and bend the other side of the triangle inward. Fold the wide end of the paper in the opposite direction

6. Do all this on the other side of the product

7. It turned out to be a “pocket”. Lift the top and fold it so that the edge lies evenly along the length of the paper. Place the corner in the “pocket”. Bend the top corner down

8. Do the above step on the other side of the plane - both sides should look the same

9. Fold the part on the side of the “pocket” upward. Do the same on the other side.

10. Open the product and place the leading edge inside. Protruding sections will appear in front - bend them. Remove the rear fin-shaped parts that appear

11. Turn the product over and fold the front part. Fold in half and iron the folds

12. Make the fuselage piece: Fold one side of the piece down along a line that runs parallel to the center fold. Do the same with the second side.

13. Fold a small piece of one and the other wing upward. Unbend the product. It already has a base and flat wings

14. Run your fingers along the front of the wings to create a curve. The plane is ready and can be launched

How to make a fast paper plane?

The paper airplane will fly quickly thanks to its folded tail in a special pattern. The nose of such an aircraft should be sharp and thin.

Below are step-by-step instructions on how to make a fast paper plane:

1. Bend a sheet of paper lengthwise. Unfold it

2. Now fold the sheet in half. From the middle, fold both edges down, and then straighten half of what you folded

3. Unfold the sides that are located on the side and fold each flap inward. First do this with the inner lapels, then with the outer ones.

4. Bend some of the wings back. Bend the wings from the bottom a short distance

5. Run your finger or ruler along the fold line and straighten the wings

6. Bend the resulting folds parallel to the folds of the wings. The plane is ready

How to make a good flying paper airplane?

Any paper airplane, if folded correctly, will fly well.

Tip: Carefully iron all bend lines with hard objects or fingers.

Tip: To make origami products, use only flat sheets of paper.

If a child comes up to you and asks how to make a paper plane that flies well, advise him to make a product with flaps or a complex “tail.” Such models fly far and high.

Important: The patterns for these models are described above, so you can start creating on your own or with your child.

How to make a fast and easy paper airplane: tips and reviews

As you have seen, there are many ways to make paper airplanes. It's easy to make a fast and light paper airplane. Tips and reviews will help you avoid mistakes and become an origami master.

Tip: If you are new to origami, try to make only simple models at first. When the paper begins to “listen” to you and you feel that the airplane models fly well, then begin to master more complex and unusual models.

Important: Before you start making the plane, prepare your paper. Prepare several sheets, as at first it will be bad for you - everything comes with experience.

Tip: Do not use wrinkled sheets of paper. An airplane cannot be made from bent and torn sheets.

Tip: Try to keep the product symmetrical about the axis (imaginary or real). If this is not observed, the plane will fall on its side during flight.

Make several models and organize a real air show on the street with your child. Remember your childhood - fly a paper airplane!

Video: Paper airplane

Hi guys! In this material we will talk about how to make paper airplane for 100 meters flight . Generally speaking, almost any aircraft can fly quite far - it all depends on the altitude from which it was launched. The design features of paper airplanes affect their ability to glide. So an airplane that can glide for a long time will fly for a very long time and far from a height, for example, the 16th floor. The wind will additionally help speed up and prolong the flight of such a paper craft. Let's start our rating of the farthest flying aircraft.

5th place - the simplest paper airplane models

In this place there are all the simple models of airplanes that even a child can assemble and which we all assembled in class and taught to the girls and teachers. For such tasks, ordinary blunt-nosed airplanes and gliders are quite suitable. Here are 10 of the best easy-to-assemble paper airplanes.

This is the simplest and most popular paper airplane - almost all people know it because they have been collecting it since childhood.

The following aircraft model has a fast and smooth flight. Due to the front supporting wings, the nose does not collapse, providing stabilization, lift and long flight.

The next one will be a blunt-nosed aircraft with increased collision resistance.

The fifth will be assembling a modified plane with a blunt nose. The circuit is simple, but requires careful assembly.

Now I propose to assemble a good airplane from paper with nose wings and vertical rear stabilizers. The shape of the wing of such a glider allows you to fly longer in a straight line.

The next plane has a sharp nose and flies rapidly forward. The fins on the wings stabilize and prolong the flight of such a paper fighter.

The following design has good piercing abilities - the craft looks like a space fighter. It seems that it was created to exterminate enemy personnel.

The largest wings are those of a glider, which has a rather ridiculous appearance. But this does not prevent him from flying very long and far.

The amazing design of this airplane makes it look like a space shuttle or a Boeing. He flies not far, but effectively.

4th place - paper plane "Albatross"

We bend a sheet of A4 paper in half and draw it with our fingernail so that the fold is perfect.

We bend the edges of the paper inward towards the central axis.

After this, we bend the edges at an obtuse angle again towards the center. The edges of the paper should lie symmetrically on the central axis of our craft.

Then we bend the nose of the paper airplane towards the tail and align the centers of symmetry.

Add corner folds so that the left side is parallel to the right side.

We bend it back and bend the sharp nose of the plane back along the flight path. We iron all the seams with our nails.

We bend the wings so that a large area of the wings remains load-bearing. We do everything extremely symmetrically so that the plane can fly further.

At the end we form the tail. In principle, the bend of the tail can be done as in the photo of any size.

We straighten the resulting bends upward so that it ends up in the space between the wings.

We bend the vertical stabilizers upward parallel to the main axis of symmetry of the paper airplane. This is the plane we have - try to fly it quickly.

If you still have any questions about assembling this aircraft, then watch the detailed video with comments.

3rd place - diagram of an airplane made from paper “Hawk”

Now we will assemble another complex aircraft.

First step. Fold the sheet in half exactly in the middle. The quality of the flight will depend on the evenness of the folds. All stages of the aircraft are done in a mirror manner - left and right.

Second step. We bend the left and right sides towards the center.

The third step is to once again take the left and right edges of the paper and bend them towards the central axis of the plane.

The fourth step is to bend the sharp end of the workpiece towards the tail. In this case, the bend line of the sheet should pass through the point of intersection of the edges in the middle of the paper craft. Centering is checked by matching the central bend along the long side of the sheet.

Fifth step. We bend the edges of the paper on the left and right again towards the center, as in the photo. It is important here that the inner layer of paper does not bend or form wrinkles.

Sixth step. We grab the outer fold and open it, and then wrap it inward as shown in the photo. We do the same from the other side of the plane. We take the formed pockets and bend them inside out.

Seventh step. The pointed nose needs to be bent in the opposite direction about 1 cm deeper than the logical fold line. Pockets are formed there, which we bend inside the nose from approximately the middle.

Step eight. We also wrap the tip opposite the sharp nose.

Ninth step. We bend the paper airplane wings parallel to the keel. If the wings of your paper craft match, then the base of the airplane is assembled symmetrically.

Tenth step. We bend the edges of the wings parallel to the main axis of symmetry to form flaps. The plane is ready.

A detailed video on how to assemble such an airplane with your own hands from paper is given below.

2nd place - diagram of an airplane made from paper “Thunderstorm”

We will continue to assemble a paper airplane that will fly for a long time according to a highly complex assembly scheme. We will need, as always, a sheet of A4 paper. This can be plain white or colored paper. You can also take sheets from magazines with medium paper thickness.

The first step is to bend the sheet in half. We remind you that depending on how smoothly and symmetrically your plane is assembled, it will fly in exactly the same way. After bending the sheet in half, unbend it and then move on to the second step.

The second step is to bend the corners to the center - on one side and the other. It turns out to be such a preparation.

Third step. The edges of the paper that formed an obtuse angle on the left are correctly bent again along the line of the nose of the aircraft to the right corners of the paper blank. See how it looks in the photo. Straighten the folds of the paper near the nose especially carefully so that everything is symmetrical.

Fourth step. We see a point at the intersection of the bends of the left and right edges of the workpiece. Along the line through this point you need to fold the airplane in half, as shown in the photo. You can check yourself by matching the lines of the central fold. After bending, unbend, turn over and bend in the opposite direction.

Fifth step. Turn the plane over again and fold the sides on the left and right towards the edge of the inner sheet. See photos and videos for more details.

After this, turn the plane over again and bend the nose forward again.

We turn it over again and turn the strip of folded paper towards the tail of the aircraft blank.

Sixth step. We bend the plane along the central longitudinal axis. It is convenient to bend the stabilizers on the wings in this position parallel to one and the other side.

Seventh step. We bend the wings to the base. Here you can bend it in different ways and experiment, but it is considered optimal to bend it from the nose to the fender liner.

Everything should fit together smoothly and be symmetrical. Then the paper plane will fly exactly 100 meters or more and not lean left or right.

If the plane is going to fly downwards, then you need to bend the back of the wings slightly upward. Thus, the flow of oncoming air will lower the tail of the aircraft and raise the nose up.

1st place - paper airplane diagram “Falcon”

This is probably one of the most beautiful paper airplanes that you can make with your own hands, because it is very similar to the real thing. To fold such a long-flying airplane with your own hands, follow the detailed instructions with photos and videos at the end.

1 – take a sheet of medium-weight A4 paper and fold the sheet in half to make a paper airplane.

2 - fold a sheet of paper in half for the longest-flying paper airplane.

3 - fold the paper along the edges to make a cool airplane with your own hands.

4 - we also bend the second side of an airplane made from a sheet of paper.

5 - iron the resulting corners of the paper airplane in half again.

6 - open each wing of the plane and turn them around.