How to sew white gloves with your own hands. We sew gloves and mittens for different occasions

Gloves made of thin material that fit the hand have an amazing charm, emphasizing grace, fragility and femininity. How to sew gloves with your own hands if you can’t find something that fits your hand well in stores?

Don't be afraid to make your own gloves. There are no particularly complex components in their manufacture. The only thing you should be prepared for is that the seam allowances will be very small and you will have to sew almost to the very edge. But it's not as difficult as it seems.

Preparing the pattern

The easiest way to make a pattern for gloves with your own hands is to remove them from old gloves by ripping them apart at the seams. But you can draw it yourself. Measure the circumference of your hand around the knuckles without thumb, divide this figure in half. Half of the glove pattern should have this width. If the pattern is smaller, enlarge all the pieces while maintaining proportions. It is most convenient to do this in some graphic editor.

Choosing fabric

Gloves made from thin skin. But when sewing leather, it requires not only special skills, but also special equipment. Standard metal foot for sewing machine does not slip on the skin, so you will have to purchase a special leather foot or walking foot. You will also need skin needles.

Can you sew long ones? leather gloves in the spirit of Grace Kelly

You can sew quite warm and beautiful gloves with your own hands from thick knitwear, fleece and even suit fabric with the addition of elastane. The main requirement for the fabric is that it should not fray too much. Otherwise, all the work will go to waste before it even begins.

Cutting out the details

The main part of the glove should be cut with a fold along the index finger, but the hole for the thumb should be cut only on one side. Don’t forget that your hands are different, so the patterns should be mirrored. This applies to all details. Do not make too large seam allowances on individual parts of the fingers; sewing them in will be awkward. Let all allowances be the same - 3-5 mm.

One pattern for all occasions: gloves for the bride

We sew gloves with our own hands

The main question that will torment you at this stage is how to sew gloves with your own hands and not mix up the parts? On the pattern, each piece is marked with letters and color. After cutting, carefully place them on the table in order; you can mark the letters on the parts with a disappearing felt-tip pen on the fabric.

You need to start with your thumb. Sew it lengthwise and insert it into the hole. Make sure that the face and back are not mixed up. Then stretch your index finger and middle fingers in one line and sew the first strip first to the top of the glove, then to the bottom. If you succeed, you can do it a few more times.

Lastly, close the seam along the edge of the palm from the end of the little finger. To make the gloves fit better on the hand, it is better to cut off excess allowances to 3 mm. Turn the gloves inside out and tuck the edges of the bells inward.

Gloves for an evening dress or short “kissing gloves”

“Biker” ones look very stylish.

Is it difficult to sew gloves with your own hands?

This post will also be useful for those who want to knit openwork gloves themselves. So, let's begin.

Gloves, in all their fantastic variety of colors, lengths and materials, are back in fashion and a must-have for good clothed woman. Whether it's a pair of long sexy gloves made of stretchy satin or a cool and elegant model made from the finest husky - they will leave few people indifferent.

The renewed interest in this most eternal of fashion accessories applies not only to Gaultier creations, Louis Vuitton, Prada and Hermes. In the nightclubs of major cities around the world, gloves are becoming a fashion statement. It's never been easier to choose the right pair of gloves for your... the right occasion- from short leather models during the day until evening, black elbow-length gloves.

Hand measurement

Glove size is the circumference of the palm, expressed in Parisian inches, measured at the base of the fingers.

Along with the actual size of the gloves, other dimensional characteristics are also important for the correct design of the glove. The finger length that deviates from the standard should be determined. It is necessary to remember: the length of each finger is measured from the highest point at the base of the finger to the tip of the finger. The length of the thumb is also determined.

Ampon is a dimensional feature that is measured from the base of the thumb to the base of the index finger.

Ribs are the main dimensional feature for determining the length of a glove. Ribs are measured from the muscle tuberosity at the base of the thumb (wrist) to the desired length.

It is useful to indicate additional information about deviation of the hand shape from the standard (for example, a long, narrow hand, short and thick fingers, etc.).

In addition to complete information about dimensional characteristics, data on the material and processing technology is needed.

Materials: nappa, suede, velor leather, jersey, elastic fabrics.

Glove lining: knitted, wool, silk lining, fur lining (short hair).

Glove seams: rustic (cuts outwards) hand and machine seams, traditional machine seams (cuts on wrong side), various decorative seams.

The most common units of measurement in glove production are:
"Parisian" inch = 27.07 mm
English square foot = 9.29 square decimetres.

Construction of a drawing of gloves

The value of the dimensional attribute Palm circumference divided by 8.

19.2:8 = 2.4 cm.

Draw five vertical lines about 20 cm long with an interval of 2.4 cm. Draw a horizontal line approximately in the middle (to mark the finger lengths).

On the little finger area, move 1 cm down from the horizontal and draw another horizontal line here (the base of the little finger on the hand is lower than the other fingers).

From the horizontal lines, plot the resulting finger length values upward. Draw horizontal lines through the resulting points and divide them in half.

Create rounded lines for your fingertips.

Draw a hole for the thumb; to do this, along the 0/1 line, move 5 cm down from the horizontal (Ampon). From the resulting point, set aside another 5 cm (the length of the muscle tubercle at the base of the thumb).

Set aside 0.5 cm inward from the right outer line and line 2/3.

From a point on the 0/1 line, 5 cm away from the horizontal, set aside 2 cm upward. From the resulting point, set aside 1.1 cm horizontally to the left and right (if your palm is wide, you can set aside higher value). Make the top section of the hole for the thumb.

From the resulting horizontal line, move 1 cm upward along the 0/1 line. Through this point (on the 0/1 line) draw a line 2.1 cm long from the upper left point - a slot for the thumb (if you have a large hand, the line may be longer). Draw line segments c and d.

From the mark corresponding to the lower point of the hole for the thumb (from the lower point of the muscle tuberosity), place the Rebras (corresponding to the length of the glove). Connect the bottom point of the thumb hole with points 0.5 cm away from the vertical lines.

The following materials are cut out (for one glove):
1 piece with thumb hole;
1 piece without thumb hole - for the upper part of the glove.

Drawing a thumb drawing

Draw mutually perpendicular vertical and horizontal lines. Vertically from the intersection point, put the length of the thumb up, down - the length of the muscle tubercle at the base of the thumb.

Horizontally set aside from the vertical line to the left and right the value of the circumference of the thumb plus 1 cm.

From the top point of the vertical line, set aside 1 cm to the left and right and draw rounded lines for the fingertip. Draw a smooth line (see drawing) on the lower section of the part for the thumb through the bottom point of the drawing.

The length of the line should be the circumference of the thumb hole plus 2.1 cm.

From the horizontal line, set aside 2.1 cm (b) upward along the outer contour of the part to determine the location of the segment d/c.

Along the horizontal line, place 1.5 cm to the left of right side external contour of the part.

From the end point of segment b (2.1 cm up the outer contour of the part from the horizontal) towards a point 1.5 cm away from the outer contour of the part, draw a segment 2.2 cm long.

Middle finger parts

Draw the middle parts for the fingers in accordance with the drawing. The base line of the fingers is equal to the width of the fingers in the glove drawing (2.4 cm).

All middle parts for the fingers, shown in the drawing once at a time, are cut out of the material (for one glove).

Glove sewing technology

Connect the parts manually or by machine in accordance with the markings (the seam processing allowance is 0.2 cm).

The connection of the thumb part with the glove part should begin at the hole slot and grind sections a, b, c, d of the thumb part with sections a, b, c, d of the glove, respectively.

Then sew the thumb piece into the thumb hole on the glove.

Sew together the middle parts for the fingers at the base: the part for the little finger - with the first part for ring finger, the second part for the ring finger - with the first part for the middle finger, the second part for the middle finger - with the part for the index finger.

The interconnected middle parts for the fingers are connected to top part gloves.

Connect the lower part of the glove with the thumb part sewn in to the upper part of the glove.

The outer sections of the glove parts are joined last.
Glove length standards

When determining the length of gloves, the number of loops/buttons of the fastener matters. Although loop and button closures on gloves have almost completely fallen into oblivion due to the widespread use of elastic materials, the classic “button length” still defines the norm for glove length. The length standard corresponds to the measured distance between the joint seam of the part for the thumb and top edge gloves The unit of measurement for the uncovered part of the hand is the French inch.

Let's start with the shortest gloves:

Two buttons: These gloves traditionally have an overall length of 20-23 cm and end at the middle of the wrist, revealing the beauty of the forearm and hugging the hand. Hole with inside On the one hand, the wrist serves as an eye catcher, and on the other hand, it makes it easier to put on the glove. So-called palm-length gloves of this type can be worn all year round.

Four buttons: a glove 25-28 cm long, covering most of the wrist. A good compromise for a woman who wants to declare her elegance. These gloves look especially good under jacket cuffs.

Six buttons: another compromise, quite exciting. It's less extravagant than the eight-button option, but it's an attractive length that will allow the wearer of the gloves to even glance at the watch - even if that's sometimes difficult! These gloves should be worn with bare hands or under a jacket.

Eight buttons: the glove reaches to the middle of the forearm. These are traditional three-quarter gloves that cover the forearm by 14-15 inches. Although the return of these gloves to fashion is not as obvious as with other styles, this is exactly the length that simply radiates charm in the Jackie Onassis style.

Twelve buttons: the so-called queen of gloves, which reaches to the elbow. Such gloves were worn by Audrey Hepburn and a whole horde of fashion trendsetters.

Sixteen Buttons: A classic 24-inch-long opera glove that ends exactly midway between the elbow and shoulder. The basic rule for opera gloves: the shorter the sleeve, the longer glove. Therefore, opera gloves should be worn with sleeveless dresses, with short sleeves, without straps or with straps, but without sleeves, as well as with evening dresses with short sleeves.

At the beginning of the last century, fingerless or classic gloves were a mandatory accessory for ladies from the noble and middle class. Now the fashion for them and mitts is returning. Openwork, made of beautiful guipure material, they adorn the bride’s hands. And some can be worn on other, no less solemn occasions.

Selecting an accessory to match your look

It's not just white models that are popular. It all depends on what image you need to create.

Products in white, pink and its shades, ivory or ecru will match the romantic style.

Black gray, dark blue colors will appeal to teenagers and adults.

Suitable for more daring women bright colors. But children's ones can also be made in the same color.

Beauty guipure, you can evaluate the variety of its shades and choose the fabric to your liking in the “” store.

How to sew gloves from guipure?

The glove should fit your hand, but not squeeze it. Therefore, the material should be selected as elastic.

It is important to determine not only the size, but also the length of the hand and fingers. The size itself is the circumference of the base, expressed in inches. If you only tape measure, then the resulting figure should be divided by 2.54.

Guipure gloves pattern. Where can I get it? You can undo old satin or any thin models. Or redraw one of the drawings suggested below. The first of them (1 square = 2 cm) is given for size 6. That is, the length of the base of the palm is 6 inches or 15.24 cm. The second one must be scaled to your measurements.

Transfer the pattern to the fabric.

Cut taking into account allowances.

Make slits on the parts according to the markings.

The wide part is the thumb. For ease of sewing, numbers indicate the places of alignment.

The narrow and long part is the remaining fingers. You need six of these parts for each hand. They can be cut with a fold. Then you will need three double elements.

Sew the thumb element to the main one. Start from the slot, matching the areas marked with numbers.

Sew the pieces for the other fingers at the base in pairs if you did not cut them out with a fold.

Sew the “fingers” to the top of the main element.

Then do the same with the bottom part.

Now you can make the external seams.

Fold open edge and hem.

If the gloves need to be long, run an elastic band or a hat elastic along the outer edge.

As you can see, sewing guipure gloves with your own hands is quite simple.

How to sew mitts from guipure?

This variation is suitable for girls, women, and girls. There are two ways to sew.

Take the glove pattern as a basis, cut off the fingers in the drawing and then follow the technology described above.

The second one is much simpler. These fingerless gloves can be created while watching a movie.

Print the drawing or draw it with your measurements. Transfer to guipure and cut out.

Place the two pieces facing inward and sew along the outer edge.

Leave a hole in the seam for your thumb or grab the product along the top edge.

Ready.

You can make a more romantic variation in wedding style. The pattern of fingerless gloves changes at the same time. You can extend it with a corner to the middle finger, make it longer.

Tip: before cutting out fabric, first cut out the scallop along the guipure so that the edge of the product is openwork. There is a second finishing method - processing the cuts with bias tape or a strip of matching lace.

Both gloves and mitts can be decorated to your liking. Glue on rhinestones, trim with beads, fur, and sew on your wrist a bow made from ribbon that matches the color of the item.

You can sew it yourself while spending a minimum of money and time. The most important thing is to choose openwork lace, which will look good on the hand. In this master class, the site will tell and show how to sew a “wedding fingerless gloves”, i.e. wedding mitts.

So, in order to sew wedding gloves yourself, you will need the following materials:

Stretch lace 15 cm wide. You will need about 50 cm (depending on the girth of your arms);
White satin ribbon 2 cm wide;
Adhesive glass stones or sewing accessories with stones;
Threads, scissors, super glue.

We measure the hand: we wrap it around the lace and make marks, or we pin off the lace at the joint. Cut off two of these pieces.

Once again we clasp the hand and now make more precise marks: one side is narrower, the other is wider. We fold the segments in half and use a ruler to connect the places of the marks - we get an oblique line.

We cut off the excess fabric and sew the edges on the machine.

Let's try on the glove. The seam should go exactly along the middle of the middle finger. Between big and index fingers We connect the lace with a pin, manually secure this joint well with several stitches. That's it, the bulk of the work is done.

Now let's get to the fun part - decorating our gloves. You can sew two gathered strips of narrow lace in a circle, stepping back a little from the edge, or embroider gloves with beads and bugles. IN in this case bows will serve as decoration. To make them we will need 2 pieces of tape about 24 cm long.

We process the edges of the tape, carefully burning them with a match. Fold a little more than half of the ribbon into a figure eight and stitch in the middle. From the remaining piece of ribbon we form part of the bow as shown in the photo, stitching in the middle. We make the second bow in the same way.

We glue sewing accessories with pebbles to the centers with super glue. Fittings in the shape of a circle or oval will look good; do not choose too massive and heavy decoration. Finally, we sew the bows to the gloves.

To sew these with your own hands wedding gloves without fingers (mitts) it took less than an hour.

Glove size is the circumference of the palm, expressed in Parisian inches, measured at the base of the fingers.
Glove pattern
Along with the actual size of the gloves, other dimensional characteristics are also important for the correct design of the glove. The finger length that deviates from the standard should be determined. It is necessary to remember: the length of each finger is measured from the highest point at the base of the finger to the tip of the finger. The length of the thumb is also determined.
Ampon is a dimensional feature that is measured from the base of the thumb to the base of the index finger.
Ribs are the main dimensional feature for determining the length of a glove. Ribs are measured from the muscle tuberosity at the base of the thumb (wrist) to the desired length.
It is useful to indicate additional information about the deviation of the hand shape from the standard (for example, a long, narrow hand, short and thick fingers, etc.).
In addition to complete information about dimensional characteristics, data on the material and processing technology is needed.
Materials: nappa, suede, velor leather, jersey, elastic fabrics.
Glove lining: knitted, wool, silk lining, fur lining (short hair).
Glove seams: rustic (cuts on the outside) hand and machine seams, traditional machine seams (cuts on the wrong side), various decorative seams.
The most common units of measurement in glove production are:
"Parisian" inch = 27.07 mm
English square foot = 9.29 square decimeters

Construction of a drawing of gloves

Glove pattern
The value of the dimensional attribute Palm circumference divided by 8.
19.2:8 = 2.4 cm.
Draw five vertical lines about 20 cm long with an interval of 2.4 cm. Draw a horizontal line approximately in the middle (to mark the finger lengths).
On the little finger area, move 1 cm down from the horizontal and draw another horizontal line here (the base of the little finger on the hand is lower than the other fingers).
From the horizontal lines, plot the resulting finger length values upward. Draw horizontal lines through the resulting points and divide them in half.
Create rounded lines for your fingertips.
Draw a hole for the thumb; to do this, along the 0/1 line, move 5 cm down from the horizontal (Ampon). From the resulting point, set aside another 5 cm (the length of the muscle tubercle at the base of the thumb).
Set aside 0.5 cm inward from the right outer line and line 2/3.
From a point on the 0/1 line, 5 cm away from the horizontal, set aside 2 cm upward. From the resulting point, set aside 1.1 cm horizontally to the left and right (if your palm is wide, you can set aside a larger value). Make the top section of the hole for the thumb.
From the resulting horizontal line, move 1 cm upward along the 0/1 line. Through this point (on the 0/1 line) draw a line 2.1 cm long from the upper left point - a slot for the thumb (if you have a large hand, the line may be longer). Draw line segments c and d.
From the mark corresponding to the lower point of the hole for the thumb (from the lower point of the muscle tuberosity), place the Rebras (corresponding to the length of the glove). Connect the bottom point of the thumb hole with points 0.5 cm away from the vertical lines.
The following materials are cut out (for one glove):
1 piece with thumb hole;
1 piece without thumb hole - for the upper part of the glove.

CONSTRUCTION OF THE DRAWING OF THE THUMB

Draw mutually perpendicular vertical and horizontal lines. Vertically from the intersection point, put the length of the thumb up, down - the length of the muscle tubercle at the base of the thumb.

Horizontally set aside from the vertical line to the left and right the value of the circumference of the thumb plus 1 cm.

From the top point of the vertical line, set aside 1 cm to the left and right and draw rounded lines for the fingertip. Draw a smooth line (see drawing) on the lower section of the part for the thumb through the bottom point of the drawing.

The length of the line should be the circumference of the thumb hole plus 2.1 cm.

From the horizontal line, set aside 2.1 cm (b) upward along the outer contour of the part to determine the location of the segment d/c.

Along a horizontal line, set aside 1.5 cm to the left from the right side of the outer contour of the part.

From the end point of segment b (2.1 cm up the outer contour of the part from the horizontal) towards a point 1.5 cm away from the outer contour of the part, draw a segment 2.2 cm long.

MIDDLE FINGER DETAILS

Draw the middle parts for the fingers in accordance with the drawing. The base line of the fingers is equal to the width of the fingers in the glove drawing (2.4 cm).

All middle parts for the fingers, shown in the drawing once at a time, are cut out of the material (for one glove).

Glove sewing technology

Connect the parts manually or by machine in accordance with the markings (the seam processing allowance is 0.2 cm).

The connection of the thumb part with the glove part should begin at the hole slot and grind sections a, b, c, d of the thumb part with sections a, b, c, d of the glove, respectively.

Then sew the thumb piece into the thumb hole on the glove.
Sew the middle parts for the fingers together at the base: the part for the little finger - with the first part for the ring finger, the second part for the ring finger - with the first part for the middle finger, the second part for the middle finger - with the part for the index finger.

Connect the interconnected middle parts for the fingers to the upper part of the glove.

Connect the lower part of the glove with the thumb part sewn in to the upper part of the glove.

The outer sections of the glove parts are joined last.

Glove length standards

When determining the length of gloves, the number of loops/buttons of the fastener matters. Although loop and button closures on gloves have almost completely fallen into oblivion due to the widespread use of elastic materials, the classic “button length” still defines the norm for glove length. The length standard corresponds to the measured distance between the seam of the thumb joint and the top edge of the glove. The unit of measurement for the uncovered part of the hand is the “French inch”.

Let's start with the shortest gloves:

Two buttons: These gloves traditionally have an overall length of 20-23 cm and end at the middle of the wrist, revealing the beauty of the forearm and hugging the hand. The hole on the inside of the wrist serves as an eye catcher on one side, and on the other hand makes it easier to put on the glove. So-called palm-length gloves of this type can be worn all year round.

Four buttons: a glove 25-28 cm long, covering most of the wrist. A good compromise for a woman who wants to declare her elegance. These gloves look especially good under jacket cuffs.

Twelve buttons: the so-called queen of gloves, which reaches to the elbow. Such gloves were worn by Audrey Hepburn and a whole horde of fashion trendsetters.

Sixteen Buttons: A classic 24-inch-long opera glove that ends exactly midway between the elbow and shoulder. The basic rule for opera gloves is: the shorter the sleeve, the longer the glove. Therefore, opera gloves should be worn with sleeveless, short-sleeved, strapless or strapless dresses, as well as evening dresses with short sleeves.

P.S.: people, you will make peppers, Special attention Pay attention to the details between your fingers. according to this tutorial, it turned out that (I made myself gloves without fingers) the fingers turned out to be trash flares, but maybe I’m missing something, but I warned you *O*