Menu
homeChildren holidays

Decorative patches for jeans. How to install an invisible patch

It happens that the damaged area of ​​\u200b\u200bthe fabric cannot simply be mended, in this case they resort to patches. At the same time, the whole variety of patches can be conditionally divided into two main types: decorative and functional. At the same time, functionality does not always exclude decorativeness, but a decorative patch can even be applied to a product without any damage. By the way, such a patch can hide not only holes, but also old spots.

Decorative patches

Such patches look especially good on children's things, they can be deliberately distinguished by finishing seams, braid or cords. Knitted patches look good, especially if they are individual elements- cars, bear cubs, clouds. In this case, they already resemble applications, and therefore few will guess that they hide a worn knee or an unwashed grass stain.

To hide damage to the fabric, you can put on top ready application, sold in almost any fabric store. Depending on the method of manufacture, it will either need to be sewn along the edge or glued with an iron.

Functional patches

Since such patches should be as discreet as possible, they are made from the same fabric as the product itself, or at least a very similar material. Before cutting a piece right size, the fabric must be washed and steamed so that the fabric shrinks. If you use unprepared material, it can then sit down and pull the product together.

When applying a patch, be sure to ensure that its share thread coincides in direction with the share thread of the product. If the thing is torn near the seam, this seam must be unraveled and the edge of the patch inserted into the resulting hole, then sew on the patch and sew up the loose seam.

When mending things made of bright fabrics with clear patterns, patches are applied to the front side of the product, making sure that new fragment matched the pattern with the surface of the fabric.

patch with stitching

Cut out the part for the patch, making it 7-9 mm larger than the hole in the fabric, and put it on the product, evenly closing the hole. Baste the patch, sew an overcast seam along the edge of the hole, and do not forget to make notches in the corners so that the seam does not pull the fabric. Next, securely sew the patch with small stitches of the “forward needle” seam (fig.).

Rice. patch with stitching

Patch over the edge

Cut out the part for the patch, making it 10 mm larger than the hole in the fabric, and place it on the product, evenly closing the hole. Make notches of 5 mm in the corners of the hole in the fabric and on the patch, bend them to the wrong side. The patch and the hole in the fabric should now be the same size. Gently sew the patch into the hole, running small stitches over the edge. Finish open sections with an overlock stitch after patching or in advance, depending on how much the fabric is crumbling (fig.).

Woven patch

Cut out a patch from a suitable material, the sides of which exceed the sides of the hole by 50-60 mm. Then begin to carefully remove the weft threads from the top and bottom of the part and the equity threads along its edges. As a result, you should have a flap of fabric that matches the size of the hole, surrounded on all sides by a fringe of the same length. Baste this flap along a straight thread (fig.).

Rice. Woven patch

Pick up a very thin needle and thread a thin silk thread into it with both ends to make a loop at the end of the thread. Insert the needle next to the first thread of the fringe, sew a few blind stitches to the edge of the patch, pull the thread about half its length, thread it into the resulting loop of the fringe and pull the thread to the end. The fringe along with the thread will be on the wrong side of the product. Hide all other fringe threads in the same way.

If you think that self-repairing clothes requires sewing talent, you are wrong. You can sew on fashionable patchwork patches for clothes yourself, even if you are not very familiar with the sewing machine.

Warm cardigan with suede patches, thin T-shirts with long sleeves and decorative inserts from another fabric, trousers with patches on the knee, between the legs and in other places - these are all fashion touches modern clothes. Patches can be barely noticeable or very bright. Often their material is completely different from the original.

How, without spending a penny, you can turn old forgotten clothes into models that are popular in the upcoming season?

It's simple - you can do it fashionable patch on jeans. In addition, many people just fall in love with some jeans and when they wear out, they don't want to part with them, because they are very comfortable and they like it. Do not immediately part with your favorite things, easy repairs will help to quickly revive them.

How to sew patches on jeans with your own hands

There is a very easy way to spruce up your favorite pants or cover up a worn knee with a trendy tweed or denim patch.

You will need:

  • trousers;
  • needle and thread, although everything can be done faster using sewing machines;
  • a ready-made patch for jeans or a piece of material from which you will make a patch.

The material for the patch can be selected to match the trousers. And you can make contrasting accents. It can be a different type of fabric, leather or its substitute, fashionable suede, tweed. IN currently can be purchased in specialized stores ready-made patches processed along the edges different forms from various materials all sorts of colors.

How to make patches for jeans with your own hands on the knee:


  1. First of all, you need to prepare a patch. You can do this with a piece of paper
    which you need to draw an oval or another desired shape, and then, transfer the prepared template to the material and cut out the patch;
  2. The edges of the patch must be sheathed carefully so that they do not wear out;
  3. With the help of a sewing machine or by hand, we sew a patch to the jeans on our knees. You can use colored threads or threads similar to the color of the material, and also choose a color contrast.

How to sew a patch on jeans between the legs step by step

If pants frayed between the legs, they can be repaired.

You will need:

  • trousers;
  • sewing machine;
  • denim material from which you will make a patch.

When choosing a patch between the legs, it is advisable to choose it in the same color as the jeans. In addition, it is necessary to consider the direction of the threads on the fabric and try to repeat it when sewing on the patch. This is necessary so that the direction of the threads on the patch matches the direction on the jeans. Then the patch will look very harmonious.

How to sew a honey leg patch onto jeans:


  1. We lay out the trousers with a torn seam in the middle;
  2. We put a plank of wood under the torn places. You need to carefully consider how you will cut out the damaged fabric;
  3. We draw the outline of the area that we will cut out;
  4. Cut out the damaged material. Usually make a patch in the shape of a circle or oval;
  5. Then, a patch is cut out for jeans from another material of the same size and shape as the damaged piece of fabric, plus a margin of 1.5-2 cm for the seams;
  6. The resulting piece of fabric must be carefully ironed;
  7. We pay attention to the direction of the threads in the fabric and compare them with the threads on jeans or cut pieces of damaged fabric;
  8. We pin the finished patches to the hole in the jeans and baste with a needle;
  9. We make a payment;
  10. We process the edges.

You can use threads of the same color as the other stitches on the trousers for the stitch, usually a contrasting white or yellow thread. The whole DIY repair process will take you about 30-40 minutes. Finding an atelier and repairing jeans in it would certainly take you more time and money.

So repair jeans or give them fashion notes very simple. Currently, patches can also be purchased at the store and this will allow you to decorate your clothes with fashionable leather or felt patches, and for children's clothing, the choice of interesting patches is even more diverse - cars and planes, popular cartoon characters, flowers, princesses, fabric with rhinestones.

Before sewing up a hole, you should pay attention to its size and frayed edges, as well as determine the type of fabric from which the torn product is made. A simple ripped seam will be much easier to sew up than a large one. torn hole on fabric. If your thing just ripped open, then you can safely sew it along the seam using strong threads for this. If, on the site of the hole, there is not enough of a significant area of ​​\u200b\u200bthe fabric, then it can be darned with threads or a patch can be applied.

Steps

Needle and thread selection

    Choose the right thread. If possible, use thread to match the torn garment. If the stitches are not visible with front side piece of clothing, then the color of the threads does not really matter. You can also take thread bright color matching or contrasting with the color of the fabric.

    Choose the right needle. If the fabric is thick and rough ( denim, leather, layered fabric), take a sharp and thick needle so that you can pierce the fabric with it without extra effort. If the fabric is thin and delicate, then you can take almost any standard sewing needle; however, you can use a thinner needle if you wish.

    • Cotton, nylon, silk, jute, blended and others thin fabrics it is better to sew with thinner needles. In this case, the needle can be either short and have a length of only 2.5–5 cm, or longer if you need it. If you use a thick needle (about 1 mm thick) to work with these fabrics, it can leave visible holes in the fabric. If desired, use a thimble to protect your finger from needle pricks while sewing.
    • If you are afraid of breaking the needle, choose a thicker needle. If your fingers hurt from the force of the needle when piercing the fabric, help the needle pass through the fabric by creating a stop on the hard surface. Some fabrics (like denim) are difficult to sew, so you have to push the needle with something hard.

  1. Make sure you have enough thread. If you are not sure about this, try attaching the existing thread to the torn place. Add an extra 25 cm to the estimated required thread length. Stitches eat up a little more thread than the direct parameters of the place being sewn, in addition, you need to have a supply of thread to tie a knot at the end of your work. Remember: the thicker the fabric, the more threads it takes to sew it up. If the fabric is thicker than 5 mm, then you may need twice as much thread.

    Insert the thread into the needle. Check that the tip of the thread is even and not fluffy. If the tip of the thread is fluffy, wet it and then twist it with your fingers so that it can easily pass through the eye of the needle. If you have trouble threading your needle, use a needle threader.

    Tie a knot. Hold both ends of the thread and tie a knot on the longer one (usually the one that did not go through the eye of the needle). This will keep the thread from popping out of the fabric when you start sewing.

    • If you are going to sew up a torn knitted thing, then you will have to make a little more effort when tying a knot. knitted clothes has very large holes between the threads of yarn, when compared with ordinary fabric. In this case, to get started, you will need to tie a fastening knot with a needle and thread on the knitted fabric itself so that the thread does not go anywhere.

    Sewing up a torn seam

    1. Find the torn seam. Compared to a regular hole, sewing up a ripped seam is quite simple. Where previously the fabric was sewn together, the thread simply broke and ripped, causing the layers of fabric to separate and form a hole. In most cases, a torn seam can be re-sewn.

      • For example, a seam can tear in a pocket, which will cause all the little things to spill out of it, and it can also disperse on a sleeve, exposing the elbow.

    2. Turn the garment inside out. Get to desired seam. Then you can lightly iron the torn area with an iron with a suitable heat setting in order to then carefully align the pieces of clothing along the old seam line.

      Lay a new seam in the footsteps of the old. This can be done manually (with a needle and thread) or on sewing machine, using smaller stitches for extra strength. When laying a new seam at both ends, go a little over the remaining intact part of the old seam. Don't forget to tie a knot when you're done sewing. At the end of the work, be sure to cut off the excess thread. br>

      • Sometimes you have to sew up a torn seam on the overhead parts of clothing, for example, on an appliqué or a patch pocket. In this case, you need to take the threads exactly in tone original threads, as these places are clearly visible. When sewing a new seam in this situation, try to keep the same stitch length as in the original stitch.

      Darning holes

      Measure the hole. If the hole is too big, you will need patching fabric. If the pocket is torn, it will also have to be sewn up. You will need a patch that is the same color as the torn fabric and large enough to cover the entire hole.

      Estimate the size of the hole. The most difficult to sew up are those holes in which a whole section of fabric is missing, for example, frayed holes on the knees of trousers or on the elbows of a jacket. Don't try to mend such holes without patching them, or you'll just pull the fabric together, distorting the garment and making it look untidy. [

      Apply a reinforcing patch. If the fabric is torn near the seam line or in the middle of the fabric (not at the seam), then you need to reinforce the torn area. Cut off a small piece of fabric of the same quality and color as the fabric of the garment. Put this scrap under the hole that has formed front side out. Then bring the edges of the hole together as much as possible without wrinkling the fabric. Install a zigzag stitch on the sewing machine and sew the edges of the hole with it, while grabbing the piece underneath to sew the hole as securely as possible.

      • The result, of course, will not be invisible, but it will turn out quite neat. If you're sewing up a piece of clothing in an informal style, then you can use a fabric for a patch. contrasting color or with a pattern, and additionally create similar patches in other places so that they seem like a decorative decoration. In this case, the patches can be applied to the front of the garment or made into appliqués to add a special design intent.

    3. Reinforce torn edges or frayed fabric with classic darning. Start sewing a line of stitches 2.5 cm from the torn area. This is especially important when the fabric has torn or thinned. Starting the darning with some distance from the hole will strengthen the fabric and prevent it from tearing further. Pass the needle through the fabric and carefully thread the dotted stitch, bringing the needle up and down. Try to stick to a stitch length of about 2 mm.

      • If the edges of the hole are very frayed, try to strengthen them special liquid against fabric fraying before darning. This will make the darning more durable.
      • If the garment is too tight, the darning may come apart when you put it on. In such a situation, try placing a reinforcing patch under the hole and mending the hole with it. Consider sewing on a button where the hole was mended, if appropriate. In any case, darn in such a way that it consists of a large number intertwined stitches.

    4. After the first row of darning stitches, lay the darning near it in reverse side second row and so on. Repeat rows of stitches in the longitudinal and transverse directions until you completely cover the hole with them.

      • If the torn fabric has crumbled heavily, then it may need a turn around the edge. Before darning, fold the edges of the hole to the wrong side and secure them with stitches. The hem can be made just single or double, so that the fabric completely stops crumbling in this place.

    5. Finish the job. Try to work carefully so that the thread does not get tangled during darning. Stretch and straighten the darned area a little. To do this, pinch the sewn area with your fingers and rub it a little to straighten out any irregularities in the darning. At the end of the work, tie a knot and cut off the excess thread.

Not every day we are faced with the problem of how to sew a patch. Most often, we send clothes with a torn hole that cannot be imperceptibly repaired to the dacha or to the scrap. However, there are people whose structure and shape of the legs constantly create conditions for wiping holes in jeans. Two or three weeks of wearing - and here is the hole again. Do you really have to run around buying a new pair of jeans every time? Or can you still sew a patch yourself, with your own hands?

Of course you can! And this process can even be called creative. Of course, if a hole appeared on a flat surface of jeans (in the thigh, shin, knee or pope), then there is just a huge scope for creativity. Starting from adhesive patches, of which there are a lot of options, and ending with original inserts made of material of a different texture and color. You can also sew on a patch in the form of a funny little man, an animal, a heart, a flower - that's what you prefer. By the way, such decorative patches are very relevant and fashionable. They make the outfit original and unusual, attract the attention of others and give your image coquetry and mischief.

However, let's return to this option, when the patch needs to be made as inconspicuous as possible. Certainly one of the most important factors at the same time, choose the most suitable material for the patch. If such incidents happen to you regularly, then you probably don’t throw away sawn-offs with long jeans. If the same matter is not found, look for it inside the back pockets of jeans. That is, you can cut inside pocket and use this fabric for patching. And in place of the cut out fabric, sew a patch from another matter, because in the pockets no one will see the color and texture of the material. The main thing is to do it carefully so that every time you take off your jeans, the look of the patches in your pockets will not separate you. raival. So, now you have the fabric for the patch.

The patch can be sewn on by machine or by hand. More often this work is done manually, as it is not always convenient to do it on a typewriter. For sewing, select the threads that are suitable in thickness and color. They can be the color of the fabric to be invisible or yellow or white color, depending on the main color of the threads with which the jeans are sewn. The patch should be cut in the shape of a hole, but 1.5-2 cm more on all sides. Place the patch facing the wrong side of the jeans. Fix it with pins in the desired position and start sewing with small, neat, even stitches in length. Stitch by stitch, back stitch is suitable for this type of darning. You can sew on the front side by bending the edge of the hole inward just a couple of millimeters. If you sew a patch on a typewriter, then you can not bend the edge, but use a “zigzag” seam, which will be almost invisible and will firmly connect the layers of matter to each other. The main thing is to do everything carefully.

When you sew a patch do not forget to thoroughly steam and iron this place.